manualshive.com logo in svg

iPECS iPECS-LIK, Feature Description & Operation

The iPECS iPECS-LIK Installer's Manual is a comprehensive guide that allows you to easily set up and customize your iPECS-LIK system. It provides step-by-step instructions and detailed illustrations, ensuring a hassle-free installation process. Download this manual for free from our website and empower yourself to maximize the full potential of your iPECS-LIK product.

Share
Download
background image

iPECS-LIK 
Feature Description & Operation Manual 

Issue 6.0d1 

 

 

291 

4.9 DIRECT INWARD DIAL (DID) 

Description 

A carrier service, known as Direct Inward Dial (DID), sends digits to the system so that the call 
may be routed directly to a specific station or system facility. Digits sent to the system are 
generally the last digits (3 or 4) dialed by the caller. DID service is available over analogue, 
digital, and packet networks. Analogue DID lines are limited to one-way incoming service and 
require special call-start signaling definition. ISDN lines can provide two-way, incoming DID and 
normal outgoing service, and require no special signaling. 

After collecting the digits from the carrier, iPECS converts the digits employing one of three DID 
digit conversion Types: 

  Type 0 - collect incoming digits based on the programmed digit count and convert the 

digits according to the DID conversion pattern, resulting in the DID destination 
number. 

  Type 1 - use the incoming DID digits as the destination number without converting. 

  Type 2 - Following the result of DID conversion Type 0, route the call according to 

the Flexible DID table conversion. 

Operation 

System 

System response to an incoming DID call (analogue CO line): 

1. set-up a connection based on the defined Start signal, 

2. collect incoming digits based on the programmed Receive Digit Count, 

3. handle digits based on the Conversion type (0-2), 

4. route the call to assigned destination. 

System response to an incoming DID call (ISDN line): 

1. set-up a connection based on the received call set-up messages, 

2. collect incoming digits and delete digits from left based on the programmed ISDN 

Remove Digit Count, 

3. handle digits based on the Conversion type (0-2), 

4. route the call to assigned destination. 

Conditions 

1. If ICLID routing is assigned for the CO/IP Line, the received Caller Id is compared to 

the ICLID Table for routing first. If Caller Id does not match an entry in the ICLID 
Table, the normal DID call processes are used. 

2. DID calls that encounter a busy signal, are not answered in the DID/DISA No 

Answer Timer, or are received at a vacant or invalid number can be routed to the 
Attendant, a tone, Station group, or VMIM/VSF announcement. When the 
Attendant receives such calls, the call is appropriately identified by the Attendant 
iPECS Phone display. 

3. For a station that is part of a non-pilot Station Hunt group, DID calls will follow the 

group hunt process if the Station is busy or does not answer the call. 

Summary of Contents for iPECS-LIK
































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for iPECS-LIK

Billion SG6200NXL Quick Start Manual preview
SG6200NXL
Brand: Billion Pages: 35
Planet ICG-2420-LTE Quick Installation Manual preview
ICG-2420-LTE
Brand: Planet Pages: 12
Matrix Telecom SIMADO GFX44 Quick Start Manual preview
SIMADO GFX44
Brand: Matrix Telecom Pages: 32
Evolvere Eugenio User Manual preview
Eugenio
Brand: Evolvere Pages: 43
AudioCodes MP-272-DB Quick Manual preview
MP-272-DB
Brand: AudioCodes Pages: 2
Ubee DDW366 Safety And Installation Manual preview
DDW366
Brand: Ubee Pages: 7
LANSITEC 100-13248 Manual preview
100-13248
Brand: LANSITEC Pages: 25
Gree ME30-44/D2 B Owner'S Manual preview
ME30-44/D2 B
Brand: Gree Pages: 24
D-Link DVG-7022S User Manual preview
DVG-7022S
Brand: D-Link Pages: 86
Tekkeon myTalker ET7000 Specification Sheet preview
myTalker ET7000
Brand: Tekkeon Pages: 2
ERT VIPER User Manual preview
VIPER
Brand: ERT Pages: 45
Optimus DVA-102ETH Operating Manual preview
DVA-102ETH
Brand: Optimus Pages: 44
B+B SmartWorx SmartSwarm 300 User Manual preview
SmartSwarm 300
Brand: B+B SmartWorx Pages: 146
Z-Wave myGate Quick Start Manual preview
myGate
Brand: Z-Wave Pages: 11
SICK RFU63x Product Information preview
RFU63x
Brand: SICK Pages: 16
Centeron CGW Series Instruction Manual preview
CGW Series
Brand: Centeron Pages: 7
Tait TN8271 Technical Notes preview
TN8271
Brand: Tait Pages: 6
ICC Mirius Installation Instructions Manual preview
Mirius
Brand: ICC Pages: 56

Brands by name

Popular brands

Load more brands