iPECS iPECS-LIK Feature Description & Operation Download Page 300 | Manualshive

Page: 300 / 447

background image

iPECS-LIK
Feature Description & Operation Manual

Issue 6.0d1

287

4.5 CO/IP RING ASSIGNMENT

Description

Each station in the system can be programmed to provide an audible signal when the system
detects an incoming call on specified CO/IP lines. Separate ring assignments are made for Day,
Night and Timed Ring operation mode. In addition, the audible signal at the station can be
delayed by 1 to 9 ring cycles allowing other stations to answer the call first.

Operation

System

Operation of this feature is automatic.

Conditions

1. Separate assignments are made for stations to ring in the Day, Night and/or Timed

Ring mode.

2. Audible alerting for an incoming VoIP call is based only on the derived IP Address.

3. A busy station receives muted ring or Call Waiting tones as appropriate for the

station’s Off-hook ring assignment.

4. The system Ring mode can be selected manually or automatically. In the Automatic

mode, Day/Night selection is determined based on the Automatic Ring Mode
Selection table. The Attendant has manual control over the Ring mode selection.

5. The LCD of the Attendant station will display Night and Timed Ring Mode and the

[DND]

button LED will flash.

6. If a CO/IP line is not assigned to ring at any station, incoming calls on the CO/IP line

will ring the first available Attendant.

Programming

CO/IP

1 CO Ring Assignment (PGM 144)

TABLES

1 Auto Ring Mode Selection Table (PGM 233)

Related Features



Day/Night/Timed/Scenario Ring Mode



Auto Service Mode Control



Off-Hook Signaling

Hardware

«
...
298
299
300
301
302
...
»

Summary of Contents for iPECS-LIK
































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for iPECS-LIK

Brand: Grandstream Networks Pages: 10

Brand: Kunbus Pages: 30

Brand: EAE Pages: 22

Brand: Toro Pages: 40

Brand: ATX Pages: 84

Brand: Seneca Pages: 52

Brand: Seneca Pages: 99

Brand: Ness Pages: 50

Brand: ADT Pulse Pages: 15

MediaAccess TG799vn

Brand: Technicolor Pages: 128

Brand: Samsara Pages: 4

Brand: RCA Pages: 44

Brand: GE Security Pages: 20

Brand: Juniper Pages: 128

Brand: OBLO Living Pages: 15

Brand: Haivision Pages: 7

Brand: RTA Pages: 73

Brand: RTA Pages: 73

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands