iPECS iPECS-LIK Feature Description & Operation Download Page 297 | Manualshive

Page: 297 / 447

background image

iPECS-LIK
Feature Description & Operation Manual

Issue 6.0d1

284

4.2 CO LINE FLASH

Description

Analog CO lines recognize a brief open or ground connection, “Flash”, as a request for new dial
tone. When used behind a PBX, a Flash is often used to activate a PBX feature or call transfer.

Operation

iPECS Phone

While connected to an analog CO line

1. Press the

[FLASH]

button, the system generates a flash on the CO line.

SLT

While connected to an analog CO line

1. Momentarily depress the Hook-switch.

2.

Dial “551”, the Flash feature code.

Conditions

1. Stations may Flash on a CO Line defined for PABX operation and will experience

COS dialing restrictions if a PABX Trunk access code is dialed.

2. During a Flash, the LED for the CO line button will remain lit.

3. A Flash may be stored as a part of a Station or System Speed Dial number.

4. While connected to an internal call or dial tone, pressing the

[FLASH]

button will

regain ICM dial tone.

5. While making a Page Announcement (internal or external, including all call paging),

pressing the

[FLASH]

button will terminate the Page Announcement and return

ICM dial tone.

6. The Flash function is not available on VoIP calls.

Programming

CO/IP

1 Flash Type (PGM 141-Btn 6)

2 CO Flash Timer (PGM 142-Btn 12)

Related Features



Station Speed Dial



System Speed Dial

Hardware

«
...
295
296
297
298
299
...
»

Summary of Contents for iPECS-LIK
































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for iPECS-LIK

ServiceRouter V2

Brand: Eurogard Pages: 23

Brand: Chipkin Pages: 30

Brand: FOR-A Pages: 36

Brand: THOMSON Pages: 52

Brand: Alcatel-Lucent Pages: 2

1898921 RSL 433 MHz

Brand: Sygonix Pages: 45

Brand: Logic IO Pages: 36

Brand: tilgin Pages: 20

Brand: tilgin Pages: 20

Brand: tilgin Pages: 20

Brand: tilgin Pages: 28

Brand: gefran Pages: 2

AMG1202-T series

Brand: ZyXEL Communications Pages: 320

Brand: ICPDAS Pages: 52

Brand: Black Box Pages: 51

Provntia MX4006

Brand: IBM Pages: 2

Brand: molex Pages: 3

Brand: RTA Pages: 69

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands