iPECS iPECS-LIK Feature Description & Operation Download Page 291

Page: 291 / 447

iPECS-LIK
Feature Description & Operation Manual

Issue 6.0d1

278

Programming

STATION

1 Page Access (PGM 111-Btn 7)

2 Internal Page Zone Access (PGM 118)

SYSTEM

1 Page Warning Tone (PGM 161-Btn 4)

2 External Control Contacts (PGM 168)

3 Paging Timeout Timer (PGM 181-Btn 9)

Related Features



Meet Me Page Answer

Hardware



External Amplifier & Speakers

3.10.2 Meet Me Page Answer

Description

Any station may respond to a “Meet Me” Page request over an Internal or External Page Zone.

The user answers the page from any station and is connected to the paging party.

Flexible buttons of an iPECS Phone may be assigned as a

{MEET ME}

button.

Operation

iPECS Phone

To assign a Flex button as a

{MEET ME}

button

[PGM]

{FLEX}

+ “544” +

[SAVE]

To answer a page with Meet Me Page

1. Lift the handset or press the

[SPEAKER]

button.

Dial “544”, the Meet Me Page code or press the

{MEET-ME}

button.

SLT

To answer a page with Meet Me Page

1. Lift the handset to receive intercom dial tone.

Dial “544”, the Meet Me Page code.

Conditions

1. A Meet Me Page must be answered within the Page Time-out timer.

2. A station may answer a Meet Me Page from any station regardless of pickup/paging

group assignments and page access permission.

3. The paging party must remain off-hook until the paged party answers the Meet Me

request. The initiator may press the Mute button to eliminate transmitting over the
page circuit while waiting for the party to answer.

Summary of Contents for iPECS-LIK
































































































































































































































































































































































































































































Search results

Summary of Contents for iPECS-LIK

Reviews:

Related manuals for iPECS-LIK

Brands by name

Popular brands

iPECS iPECS-LIK, Feature Description & Operation

Search results

Summary of Contents for iPECS-LIK

Reviews:

Related manuals for iPECS-LIK

Brands by name

Popular brands