iPECS iPECS-LIK Feature Description & Operation Download Page 164

Page: 164 / 447

iPECS-LIK
Feature Description & Operation Manual

Issue 6.0d1

151

2.63 RINGING LINE PREFERENCE

Description

A station is automatically connected to incoming calls by lifting the handset or pressing the

[SPEAKER]

button when assigned Ringing Line Preference.

Operation

iPECS Phone

To answer a call while the station is ringing

1. Lift the handset or press the

[SPEAKER]

button.

Conditions

1. When multiple calls are ringing at the station, a priority defines the order in which

calls are answered. The default priority is: Transfer > recalls > incoming calls >
queued calls

2. Intercom calls are always given the lowest answering priority.

3. Ringing Line Preference overrides Prime Line assignment.

4. SLTs operate only in the RLP mode; when ringing, lifting the handset connects the

SLT to the ringing call.

Programming

STATION

1 Auto Speaker Select (PGM111-Btn 1)

2 Ringing Line Preference (PGM 112-Btn 7)

CO/IP

1 Ring Assignments (PGM 144)

SYSTEM

1 RLP Priority (PGM 173)

Related Features



Prime Line Immediately/Delayed



Automatic Speaker Select

Hardware

Summary of Contents for iPECS-LIK
































































































































































































































































































































































































































































Search results

Summary of Contents for iPECS-LIK

Reviews:

Related manuals for iPECS-LIK

Brands by name

Popular brands

iPECS iPECS-LIK, Feature Description & Operation

Search results

Summary of Contents for iPECS-LIK

Reviews:

Related manuals for iPECS-LIK

Brands by name

Popular brands