iPECS iPECS-LIK Feature Description & Operation Download Page 155 | Manualshive

Page: 155 / 447

background image

iPECS-LIK
Feature Description & Operation Manual

Issue 6.0d1

142

2.59 NETWORK SECURITY & PRIORITY

Description

Each iPECS device (gateway Module or Terminal) supports several security and priority
protocols. iPECS devices incorporate a Web server, which will deliver the Module Web Admin
pages to a standard browser or the Module Admin may be accessed in the Terminal mode
through the RS-232 port of the Module. Characteristics that can be established are:



IEEE 802.1p/Q, VLAN

– sets Virtual LAN tag and priority for Ethernet frame



Diffserv

– sets Diffserv Code Point priority for IP packet



IPSec

– enables IPSec to establish IPSec tunnel and encryption of IP

packet



SRTP

– enables Secure RTP for RTP packet payload using AES (Advanced

Encryption Service).

Operation

System

Operation of Security and priority is automatic once configured

Conditions

1. For Web Admin, the password is encrypted using the Ericsson-LG Java Virtual

Encryption plug-in. A Java Virtual Machine (MS or Sun) must be installed in the
user’s PC to support password encryption.

2. Security and priority characteristics can be set for all devices, local or remote.

3. SRTP support is available only with the Phase 4 or higher modules. The devices

must be on the same LAN to support SRTP.

4. iPECS implementation of IPSec employs a proprietary Key exchange protocol from

the MFIM to the iPECS device.

5. IEEE 802.1 VLAN priority and ID are set at each device using the device Web

interface. Diffserv, IPSEC and SRTP treatments may also be set in the device via
the local Web interface. For the MFIM, VLANs are configured via the maintenance
interface of the RS-232 port.

Programming

BOARD

1 SRTP (PGM 132-Btn 4)

SYSTEM

1 Web Password Encryption (PGM161-Btn15)

Related Features

Hardware

«
...
153
154
155
156
157
...
»

Summary of Contents for iPECS-LIK
































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for iPECS-LIK

Brand: CHERUBINI Pages: 16

Brand: Carotron Pages: 20

NEXEDGE NX-700 series

Brand: Kenwood Pages: 3

Brand: Peak Pages: 73

Brand: National Instruments Pages: 18

Brand: Kaon Pages: 12

Brand: Lauda Pages: 24

Brand: Technoton Pages: 69

Brand: Z-Wave Pages: 17

Brand: Iseo Pages: 7

Brand: Arris Pages: 51

Brand: RTA Pages: 70

Brand: RTA Pages: 66

Brand: WAGO Pages: 16

Brand: Abbott Pages: 26

Brand: HRW Pages: 24

Brand: Metz Connect Pages: 29

Brand: Pakedge Device & Software Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands