iPECS iPECS-LIK Feature Description & Operation Download Page 145 | Manualshive

Page: 145 / 447

background image

iPECS-LIK
Feature Description & Operation Manual

Issue 6.0d1

132

2.53 LBC (LOUD BELL CONTROL)

Description

The iPECS hardware is equipped with relays that activate External Control Contacts. Each
contact is assigned to one of several functions including a Loud Bell Control. If used as a Loud
Bell Control, the contact will activate when:

External Page is accessed

Assigned Station receives ring (LBC)

UNA (Universal Night Answer) CO/IP line receives a call while in the Night or Timed
Ring mode.

Operation

System

Operation of the relays is automatic when defined

Conditions

1. The number of available contacts is given in Table 1.2-1.

2. When assigned to activate as a Loud Bell Control, CO/IP ring, transfers, and tone

ring Intercom calls to the assigned station will activate the contacts.

3. The contacts are rated at 1 amp, 24 VDC.

4. If the system is in the Night or Timed ring mode with External Night Ring enabled, a

call on a CO/IP line assigned with UNA will activate the LBC 1 contact. This
permits operation of an external night ring device. While in the Night or Timed ring
mode, LBC1 is not activated by ringing at the assigned station.

Programming

CO/IP

1 Universal Night Answer (PGM 141-Btn 7)

SYSTEM

1 External Night Ring (PGM 160-Btn 6)

2 External Contact Control (PGM 168)

Related Features



Universal Night Answer



Door Open

Hardware



External Control Contact connected to an external loud bell.

«
...
143
144
145
146
147
...
»

Summary of Contents for iPECS-LIK
































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for iPECS-LIK

Brand: 3Com Pages: 496

OfficeConnect 3CR100A97

Brand: 3Com Pages: 177

Brand: ICP DAS USA Pages: 96

Brand: ICP DAS USA Pages: 38

Brand: ICP DAS USA Pages: 17

Brand: ICP DAS USA Pages: 4

Brand: ICP DAS USA Pages: 8

Brand: HALNy Pages: 8

Brand: NETGEAR Pages: 53

PVSG-IQAN-C2E1M2W1U1

Brand: Parker Pages: 70

Fieldgate PAM SFG600

Brand: Endress+Hauser Pages: 20

Brand: 2Wire Pages: 131

Brand: ActionTec Pages: 2

Brand: Teltonika Pages: 6

OfficeConnect 3CR856-95-US

Brand: 3Com Pages: 2

3CRWE51196 - OfficeConnect Wireless Cable/DSL Gateway

Brand: 3Com Pages: 2

MiniHub Pro WLRRTES-102 TBMH110

Brand: Browan Pages: 14

Brand: Viola Systems Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands