background image

 
 

29 

6. Maintenance and Servicing 

6.1. Maintenance 

Do  not  overload  the  mount.  Do  not  drop  the  mount  as  this  will  damage  the  mount  and  /  or 

permanently  degrade  GoTo  performance  and  tracking  accuracy.  Use  a  wet  cloth  to  clean  the  mount  and 
hand controller. Do not use solvent. 

The mount worm/gear meshing can be adjusted to accommodate payload or temperature changing. 

Please refer to the instruction in Appendix.  

The  real  time  clock  battery  in  the  hand  controller  needs  be  replaced  if  it  can’t  keep the  time  after 

power off the mount. 

If your mount is not to be used for an extended period, dismount the OTAs and counterweight(s).   

6.2. iOptron Customer Service 

If  you  have  any  question  concerning  your  mount,  please  contact  iOptron  Customer  Service 

Department.  It  is  strongly  suggested  to  send  technical  questions  to 

[email protected]

  for  prompt 

response during off hour. Customer Service hours are 9:00 AM to 5:00 PM, Eastern Time, Monday through 
Friday. Call in the U.S. 1.781.569.0200. 

In  the  unlikely  event  that  the  mount  requires  factory  servicing  or  repairing,  write  or  call  iOptron 

Customer  Service  Department  first  to  receive  a  RMA#  before  returning  the  mount  to  the  factory.  Please 
provide  details  as  to  the  nature  of  the  problem  as  well  as  your  name,  address,  e-mail  address,  purchase 
info  and  daytime  telephone  number.  We  have  found  that  most  problems  can  be  resolved  by  e-mails  or 
telephone calls. So please contact iOptron first to avoid returning the mount for repair.  

6.3. Product End of Life Disposal Instructions 

This  electronic  product  is  subject  to  disposal  and  recycling  regulations  that  vary  by 

country and region. It is your responsibility to recycle your electronic equipment per your local 
environmental laws and regulations to ensure that it will be recycled in a manner that protects 
human health and the environment. To find out where you can drop off your waste equipment 
for  recycling,  please  contact  your  local  waste  recycle/disposal  service  or  the  product 
representative. 

 

6.4. Battery Replacement and Disposal Instructions 

Battery  Disposal-  Batteries  contain  chemicals  that,  if  released,  may  affect  the 

environment  and  human  health.  Batteries  should  be  collected  separately  for  recycling,  and 
recycled  at  a  local  hazardous  material  disposal  location  adhering  to  your  country  and  local 
government regulations. To find out where you can drop off your waste battery for recycling, 
please contact your local waste disposal service or the product representative.  

Summary of Contents for HEM44 Series

















































Reviews: