manualshive.com logo in svg

Invacare WALKING TUTOR WT 200, Installation And Operating Instructions Manual

Share
Download
Invacare WALKING TUTOR WT 200 Installation And Operating Instructions Manual Download Page 1

Part No 1141439

1

Walking Tutor

For more information regarding Invacare products, parts, and services, 

please visit www.invacare.com

Walking Tutor

Model No. WT 200

NOTE: Check all parts for shipping damage. In case of damage, DO NOT use. Contact 
Carrier/Invacare for further instructions.

Safety Summary

To ensure the safe and proper installation of the WT200 walking tutor, these instructions 
MUST be followed:

 

WARNING

DO NOT use this equipment without first reading and understanding this 

instruction sheet. If you are unable to understand the warnings, cautions and 

instructions, contact a healthcare professional, dealer or technical personnel if 

applicable, before attempting to install this equipment - otherwise, injury or 

damage may occur.
Invacare products are specifically designed and manufactured for use in conjunction 

with Invacare accessories. Accessories designed by other manufacturers have not 

been tested by Invacare and are not recommended for use with Invacare products.

Assembling the Walking Tutor

Tools required:
• 9/16 Open End Wrench
• 16mm Box End Wrench
• 19mm Box End Wrench
• 13mm Socket Wrench
• 16mm Socket Wrench
• 18mm Socket Wrench
• 5mm Allen Key
• 6mm Allen Key

Attaching Strap Assemblies to the Boom

NOTE: For this procedure, refer to FIGURE 1 on page 2.

1. Remove the boom cover to expose the boom crossbar (Detail “C”). 

2. Secure the strap assembly on the crossbar by placing the strap around crossbar and 

inserting the buckles through the loop (Detail “A”).

Assembly, Installation and Operating Instructions

SAVE THESE INSTRUCTIONS

Summary of Contents for WALKING TUTOR WT 200









Reviews:

No comments

Brands by name

Popular brands

Load more brands