background image

SECTION 2—EMI INFORMATION

Part No. 1122145

17

Pronto

®

 M94

SECTION 2—EMI INFORMATION

 

WARNING

CAUTION: IT IS VERY IMPORTANT THAT YOU READ THIS INFORMATION 

REGARDING THE POSSIBLE EFFECTS OF ELECTROMAGNETIC 

INTERFERENCE ON YOUR POWERED WHEELCHAIR.
Electromagnetic Interference (EMI) From Radio Wave Sources 
Powered wheelchairs and motorized scooters (in this text, both will be referred to 

as powered wheelchairs) may be susceptible to electromagnetic interference (EMI), 

which is interfering electromagnetic energy (EM) emitted from sources such as 

radio stations, TV stations, amateur radio (HAM) transmitters, two way radios, and 

cellular phones. The interference (from radio wave sources) can cause the powered 

wheelchair to release its brakes, move by itself, or move in unintended directions. It 

can also permanently damage the powered wheelchair's control system. The 

intensity of the interfering EM energy can be measured in volts per meter (V/m). 

Each powered wheelchair can resist EMI up to a certain intensity. This is called its 

"immunity level." The higher the immunity level, the greater the protection. At this 

time, current technology is capable of achieving at least a 20 V/m immunity level, 

which would provide useful protection from the more common sources of radiated 

EMI.
There are a number of sources of relatively intense electromagnetic fields in the 

everyday environment. Some of these sources are obvious and easy to avoid. 

Others are not apparent and exposure is unavoidable. However, we believe that by 

following the warnings listed below, your risk to EMI will be minimized. 
The sources of radiated EMI can be broadly classified into three types:
1) Hand-held Portable transceivers (transmitters-receivers with the antenna 

mounted directly on the transmitting unit. Examples include: citizens band (CB) 

radios, "walkie talkie", security, fire and police transceivers, cellular telephones, 

and other personal communication devices). 

NOTE: Some cellular telephones and similar devices transmit signals while they are ON, 

even when not being used.

2) Medium-range mobile transceivers, such as those used in police cars, fire trucks, 

ambulances and taxis. These usually have the antenna mounted on the outside of 

the vehicle; and

3) Long-range transmitters and transceivers, such as commercial broadcast 

transmitters (radio and TV broadcast antenna towers) and amateur (HAM) 

radios.

NOTE: Other types of hand-held devices, such as cordless phones, laptop computers, 

AM/FM radios, TV sets, CD players, cassette players, and small appliances, such as elec-

tric shavers and hair dryers, so far as we know, are not likely to cause EMI problems to 

your powered wheelchair.

Summary of Contents for Pronto M94













































































Reviews: