Invacare Hydra C650PW Owner'S Manual Download Page 14

Page: 14 / 126

Wheel Locks

Wheel locks are fitted to both drive wheels. Wheel locks should be engaged
whenever a transfer is made and / or when the wheelchair is stationary.

1. To apply the wheel locks pull the hand lever upward as Fig 39 shows.
2. To release the wheel locks push the hand lever downward as Fig 38 shows.

Fig 38 To release wheel lock

Fig 39 To apply wheel lock

3. DO NOT use the wheel locks to slow the wheelchair whilst descending an

incline.

4. Wheel locks can be adjusted as tyre wear increases. To adjust, loosen the

frame mounting clamp and slide the wheel lock upward. Retighten the
clamp while wheel lock engages to correct position. Your selling dealer can
assist with adjustment.

Please note: When the chair’s motor gearbox is engaged the motor-gearbox will act as an
electronic magnetic brake.

Summary of Contents for Hydra C650PW































































































































Search results

Summary of Contents for Hydra C650PW

Reviews:

Invacare Hydra C650PW, Owner'S Manual, Page: 14 / 126

Search results

Summary of Contents for Hydra C650PW

Reviews: