background image

Invacare® Modulite

1.

Switch off power wheelchair.

2.

Unplug actuator from actuator module.

3.

Remove screws and nuts at top

A

and bottom

B

of

actuator.

4.

Replace actuator with new one.

5.

Re-insert screws and nuts and tighten.

Replacing footboard actuator

Tools:

8 mm Allen key

16 mm wrench

1.

Switch off power wheelchair.

2.

Unplug actuator from actuator module.

3.

Remove screws and nuts at top

A

and bottom

B

of

actuator.

4.

Replace actuator with new one.

5.

Re-insert screws and nuts and tighten.

Replacing heel strap

Tools:

6 mm Allen key

8 mm Allen key

13 mm wrench

16 mm wrench

1.

Loosen and remove screws

A

and nuts

B

.

2.

Loosen and remove screw and washer

C

and nut and

washers

D

.

3.

Remove heel strap and replace by new one.

4.

Re-insert and tighten screws and nuts.

Replacing felt pads

1.

Replace worn felt pads

A

on bottom of footboard to

avoid damage to the floor.

Replacing footboard

8 mm Allen key

1.

Fig. 5-19

Loosen screws

A

on footboard

B

.

2.

Remove footboard

B

from pivot interface

C

.

3.

Insert and tighten screws

A

.

5.10.5 Replacing footboard

5 mm Allen key

1.

Loosen screw

A

on hanger, left and right side.

2.

Pull out footboard

B

and replace.

3.

Install parts in reverse order.

For adjusting footboard, see user manual of
mobility device.

5.10.6 Replacing the calf plate on the

center-mounted legrest (powered and
manual)

1/64 inch Allen key

Fig. 5-20

A manual legrest can be seen in the illustration. The
method of fixation to the seat is almost identical for both
legrests.

32

1604311-G

Summary of Contents for AVIVA RX40













































Reviews: