![background image](http://html.mh-extra.com/html/intex/purespa-sjb-hs-11/purespa-sjb-hs-11_manual_2081128007.webp)
2016-0685
2017-10-02
Maximum seating capacity:
4 adults
6 adults
Water capacity:
795 L (210 gal)
1098 L (290 gal)
Inner/outer diameter:
150/201 cm (59/79 in)
168/218 cm (66.86
Height:
71 cm (28 in)
Jet pump:
0.9 HP / 120 V / 60 Hz
0.95 HP / 120 V / 60 Hz
Bubble air blower:
1.1 HP / 110-120 V / 60 Hz
Filter pump flow rate:
1,741 L/hr (460 gal/hr)
Heater power:
1,300 Watts / 110-120 V / 60 Hz
Temperature range:
20ºC – 40ºC (68
°F - 104°F
Temperature rise:
1-1.5ºC/hr (2-3ºF/hr)
0.5-1ºC/hr
(
º / )
Number of Water Jet Nozzles:
4
6
Number of Bubble Jets:
120
140
Spa tub recommended working air pressure:
1.2 psi (0.083 bar)
Cord-connected spa with pump, heater, water jet, blower, control panel, built-in hard water
treatment, and sanitation system.
This product requires a minimum of 13 Amps. If the circuit breaker trips, please check
that no other appliances or other large loads are on the same circuit as the spa.
Site preparation and requirements
• The spa can be installed indoor or outdoor. For household use only.
• The spa must be setup on a level, flat and smooth surface that is capable of supporting the
maximum load of the filled spa
with four adult occupants: weight 1136Kg (2500 lbs); six
adults: 1592 kg (3500 lbs).
•
Make sure the area is free of sharp objects
under or around the spa.
• Provide adequate drainage system around the spa to deal with overflow water and splashes.
• Provide a properly located power outlet to connect the spa and allow easy access for periodic
testing of the cord mounted GFCI/RCD.
• Make sure there is enough clearance around the spa for full access to the spa equipment for
maintenance and/or service.
• The area shall facilitate draining purposes during long term spa storage.
Additional requirements for indoor installation
• Make sure the floor can support the full weight of the filled spa with the maximum number
of occupants. Check with a qualified contractor or a structural engineer to verify this
requirement.
• Make sure the floor is water resistant and non-slip surface. Do not install the spa on
carpet or other materials that will be damaged by moisture and condensation.
• Do not install the spa indoors on a second floor above finished living space due to the
possibility of water and humidity damage.
• Humidity is a natural side effect of indoor spa installation. The room shall be properly
ventilated to allow moisture to escape. Install a ventilating system to prevent excess
condensation, moisture in the room.
Additional requirements for outdoor installation
• Spa owners may need to comply with local or states laws relating to childproof fencing,
safety barriers, lighting, and other safety requirements. Contact your local building code
enforcement office for further details.
• Make sure the surface is level, flat, smooth and strong enough to support the full weight of the
filled spa.
• Do not setup the spa on grass or dirt, as this increases the amount of debris entering the spa, and
damage the spa floor.
• Do not expose the spa to direct sunlight for extended period of time.
It is possible to install and leave the spa outside at a temperature not lower than 4°C (39°F) provided the
water temperature inside the spa is higher than 4°C (39°F) and the water inside the circulation system,
pump, pipe are not frozen. Put a “temp barrier mat” between the spa floor and the ground to prevent heat
loss from the bottom of the spa and to provide better heat retention.