background image

345A

SAVE THESE INSTRUCTIONS

(345IO)  SAND FILTER PUMP COMBO  ENGLISH  7.5” X 10.3”  PANTONE 295U  07/10/2019

English

Page 32

TROUBLESHOOTING GUIDE

•  Line cord must be plugged into a 3 wire outlet 

  that is protected by a Class A Ground Fault 

  Circuit Interrupter, or RCD.

•  Reset circuit breaker. If circuit breaker trips 

  repeatedly, your electrical system may have a 

  defect. Turn off circuit breaker and call an 

  electrician to correct the problem.

•  Let the motor cool down and restart again.
•  Adjust the chlorine and pH level. Consult your local 

  swimming pool supply stores.

•  Load with filter sand, see “sand loading instructions”.

•  Set valve to “FILTER” position.

•  Operate the filter for longer periods.

•  Clean the strainer screen at the inlet.
•  Clear any obstructions in the intake hose by discharging it 

  inside pool wall.

•  Tighten hose nuts, check hoses for damage, check pool  

  water level.

•  Clean the pre-filtering basket more often.

•  Backwash filter.

•  Install the nozzle at the upper position of the pool inlet, and 

  the strainer at the lower position of the pool outlet.

•  Remove about 1” of sand if necessary.

•  Remove any pool vacuuming device attached to the 

  system line.

•  Make sure the inlet threaded air connector is connected to 

  the pool inlet upper hole.

•  Fill pool to correct water level.

•  Clean strainer screens at pool inlet.

•  Tighten hose nuts, check hose for damage.

•  Contact Intex service center.
•  Remove 6-way valve cover and ensure the o-ring is in place.

•  Clean sand tank o-ring with garden hose water.

•  Tighten securely.

•  Contact Intex service center.
•  Tighten/reinstall hose nut.

•  Ensure o-ring/L-shape o-ring is in place and 

  not damaged.

•  Turn off the pump and restart 5 minutes later.

•  Re-set the timer.

•  Contact Intex service center.
•  Clear any obstructions in the intake by    

  unscrewing it from the 6-way valve.

•  Contact Intex service center.
•  Use only No. 20 silica sand with particle size 

  range 0.45 to 0.85 mm (0.018 to 0.033 inches)

  and a Uniformity Coefficient less than 1.75.

•  Change sand.
•  Tighten or reinstall plunger valve.

•  Tighten air jet valve and make sure it’s 

  facing up.

•  Turn pump ON and run for few seconds, then  

  turn OFF, repeat 3 times.

•  Remove air jet valve, flush dirt out with water  

  and replace valve back.

•  Replace a new air jet valve. 

FILTER MOTOR FAILS 

TO START

FILTER DOESN’T 

CLEAN POOL

FILTER DOESN’T PUMP 

WATER OR FLOW IS 

VERY SLOW

PUMP DOESN’T 

WORK

6-WAY VALVE/COVER 

LEAKING

HOSE LEAKING

TIMER IS INACCURATE 

OR TIMER CAN'T BE SET 

PRESSURE GAUGE  

DOESN’T WORK

SAND IS FLOWING 

BACK INTO THE POOL

INLET THREADED

AIR CONNECTOR/AIR 

JET VALVE LEAKING

•  The motor is not plugged in.

•  The GFCI/RCD circuit breaker    

  is tripped.

•  Motor too hot and overload  

 

  protection is shut off.

•  Improper chlorine or pH  levels.

•  No filtering media in tank.

•  Wrong 6-way valve setting position.

•  Excessively dirty pool.

•  The strainer screen is restricting 

  the water flow.

•  Clogged inlet or discharge.

•  An air leak on the intake line.

•  Excessively dirty pool.

•  Sand media clogged with dirt.

•  Nozzle and strainer connections 

  are reversed.

•  Crusting or caking on the filtering 

  sand surface. 

•  Pool vacuuming device attached 

  to the system.

•  Inlet threaded air connector 

  connected to the wrong hole on 

  the liner.

•  Low water level.

•  Strainer screen clogged up.

•  An air leak on the intake hose.

•  Faulty motor or the impeller is jammed.
•  Sand tank o-ring missing.

•  Sand tank o-ring dirty.

•  Flange clamp not tight.

•  6-way valve damage.
•  Hose nut not securely tight.

•  Hose connection fitting 

  o-ring/L-shape o-ring missing.

•  Possible inner timer defective.

•  Clogged inlet of the pressure  

 

 gauge.

•  Pressure gauge damage.
•  Sand is too small.

•  Sand bed is calcified.

•  Plunger valve not well-fitted.

•  Air jet valve is not tight and 

  facing   up.

•  Air jet valve internal seal blocked.

•  Air jet valve internal seal dirty.

•  Air jet valve broken. 

TROUBLE

 CAUSE                                               SOLUTION

Summary of Contents for ECO15220-2




































Reviews: