manualshive.com logo in svg

Interroll ZoneControl, Operating Manual

Share
Download
Interroll ZoneControl Operating Manual Download Page 44

44 von 54

Version 2.0 (04/2019) Online

Translation of the original operating manual

Maintenance and cleaning

7 

Maintenance and cleaning

CAUTION

Risk of injury from following incorrect procedure.

 

¾

Maintenance and repair work must only be carried out by authorised and trained (specialist) personnel.

 

¾

Maintenance and repair work must only be carried out when the system has been disconnected from the 

power supply. Switch off the power to the ZoneControl and ensure that it cannot be unintentionally switched 

on again.

 

¾

Put up signs to indicate that maintenance or cleaning work is being carried out.

7.1 

Maintenance

Checking the ZoneControl

The ZoneControl itself requires no maintenance. However, in order to prevent faults from occurring, the connections 

and fixings must be examined on a regular basis.

 

¾

In the course of regular inspection and maintenance work on the conveyor, ensure that the screws of the 

ZoneControl are still tight, that the cables are still arranged correctly and that the corresponding connections 

are correctly attached.

Replacing the ZoneControl

If a ZoneControl is damaged or defective, it must be replaced.

Do not attempt to open the ZoneControl.

 

¾

Install a new ZoneControl (see „Abandonment”, page 49 and see „Installing the ZoneControl in a conveyor 

system”, page 24).

Summary of Contents for ZoneControl























































Reviews:

No comments

Brands by name

Popular brands

Load more brands