![Interpack ipg RSA 2625-TB Operations Manual & Parts List Download Page 33](http://html1.mh-extra.com/html/interpack/ipg-rsa-2625-tb/ipg-rsa-2625-tb_operations-manual-and-parts-list_2080067033.webp)
RSA2625-TB
TROUBLESHOOTING
6-1
TROUBLESHOOTING
The RSA 2625-TB Random Semi-Automatic Case Sealer is fabricated with high quality components that
provide trouble-free operation for a long period of time. However, should a problem occur, we recommend
that you consult the following table. If the problem you encounter is not discussed in this table, call toll-free
. Toll-free (877) 447-4832
Trouble
Possible Causes
Solutions
The main power is turned
on and nothing happens.
One of the fuses is burned.
Verify all fuses in the electric box.
The machine is ON but
the Infeed Guides do not
center the case on the
Infeed Table.
Compressed air supply is not
connected.
The air tubing or the valve is obstructed
or defective.
Inspect air connection and operating
pressure.
Inspect the air tubing and the valve
for leaks or obstructions.
The Infeed Guides closes
when the machine is
powered up even when
there is no case on the
Infeed Table.
The Infeed Table’s Sensor is not
aligned with his reflector.
Check the alignment of the Infeed
Sensor with his reflector.
The Top Belt Drive
Assembly stays up or
goes down too slowly.
The High Flow Pressure Regulator is
adjusted too high.
Reduce the air pressure setting of
the High Flow Pressure Regulator,
located at the infeed end of the
machine, under the left hand Side
Cover.
The Top Belt Drive
Assembly goes down too
quickly or crushes the
case.
The High Flow Pressure Regulator is
adjusted too low.
Increase the air pressure setting of
the High Flow Pressure Regulator,
located at the infeed end of the
machine, under the left hand Side
Cover.
The Top Belt Drive
Assembly raises too
slowly.
The inlet pressure is too low.
The moving parts are rubbing on
something.
Adjust the inlet pressure on the main
regulator to 80 psi and make sure
that the pressure doesn't fall below
70 psi while it is operating.
Inspect the Top Belt Drive Assembly
to make sure that noting interferes
with them.
The Top Belt Drive
Assembly does not rise
when the case pushes the
Front Sensor Plate.
The Proxy Sensor behind the sensor
plate is too far from the Front Sensor
Plate.
Remove the Front Sensor Plate and
adjust the position of the Proxy
Sensor by moving it by 1/16”, then
replace the Front Sensor Plate and
verify proper operation. Make sure
that the sensor does not touch the
Front Sensor Plate.
The cases are not taped
properly.
The tape head is not adjusted correctly. Refer to the tape head manual.
Summary of Contents for ipg RSA 2625-TB
