International comfort products F9MVE A3 Series Installation Instructions Manual Download Page 22

Page: 22 / 55

INSTALLATION INSTRUCTIONS

Gas Furnace: (F/G)9MVE

440 01 4401 02

Specifications subject to change without notice.

CAUTION

MINOR PROPERTY HAZARD

Failure to follow this caution may result in minor property

damage.
Local codes may require a drain pan under entire furnace

and condensate trap when a condensing furnace is used in

an attic application or over a finished ceiling.

The furnace can be installed horizontally in an attic or

crawlspace on either the left

−

hand (LH) or right

−

hand (RH)

side. The furnace can be hung from floor joists, rafters or

trusses or installed on a non

−

combustible platform, blocks,

bricks or pad.

Suspended Furnace Support

The furnace may be supported under the entire length of the

furnace with threaded rod and angle iron. (See

Figure 26

)

Secure angle iron to bottom of furnace as shown.

Platform Furnace Support

Construct working platform at location where all required

furnace clearances are met. (See

furnaces with 1

−

in. (25 mm) clearance requirement on side, set

furnace on non

−

combustible blocks, bricks or angle iron. For

crawlspace installations, if the furnace is not suspended from

the floor joists, the ground underneath furnace must be level

and the furnace set on blocks or bricks.

Figure 23

Duct Flanges

A10493

UPFLOW

DOWNFLOW

HORIZONTAL

YES

120

MIN

YES

120

MIN

YES

120

MIN

PERFORATED
DISCHARGE DUCT
FLANGE

Summary of Contents for F9MVE A3 Series
























































Search results

Summary of Contents for F9MVE A3 Series

Reviews:

Related manuals for F9MVE A3 Series

Brands by name

Popular brands

International comfort products F9MVE A3 Series, Installation Instructions Manual

Search results

Summary of Contents for F9MVE A3 Series

Reviews:

Related manuals for F9MVE A3 Series

Brands by name

Popular brands