AL1200TK
Transmitter and receiver setup instructions
When used in conjunction with Intermatic Inc. Low Voltage Lights:
When using something other than Intermatic Inc. Low Voltage Lights:
1
Hang timer/receiver and
plug into a GFCI outdoor
electrical outlet that has
a weather resistant cover.
Do not remove the label
covering the photocell.
2
Install 4 AA batteries into
the transmitter unit. The
transmitter unit will take
approximately one minute
to become active.
3
Plug the Intermatic Inc.
power pack into the
timer/receiver.
The timer/receiver will
now be used for the
timer operation.
4
Position the trippers
on the timer/receiver
at the “ON” and “OFF”
times used for the
lighting power pack;
then, remove the
trippers from the
lighting power pack.
5
Turn the timer/receiver
and the lighting Timer to
the “ON” position. The
lights should now be on.
6
Turn off the timer/receiver.
Press and hold the setup/test
mode button (located to the
lower left of the timer dial) for
two seconds.The receiver is
now in “setup” mode. The
photocell must be covered.
Test by moving your hand in
front of the transmitter. The
lights will be switched on for
15 seconds.
In normal operation the
lights will be turned on
for 5 minutes.
7
You should now be able
to mount the transmitter up
to 40 feet from the timer/
receiver depending on
conditions.
Place the transmitter in the
approximate location desired.
Move your hand in front of
the transmitter and verify that
it is turning the lights on.
Using the screws provided,
mount the transmitter and
aim it towards the area you
want to protect.
Test the distance and
peripheral sensitivity of the
transmitter by standing out
of sight of the transmitter
and moving into range
while observing when the
lights turn on.
Adjust the transmitter to
cover the largest, or specific
area desired. Tighten the
locking bolt.
8
Press and hold the test/setup
button for two seconds to exit
the setup mode on the
timer/receiver. Remove the
label covering the photocell.
9
To test operation at any time,
press the test/setup button
and verify that the transmitter
and receiver are working.
ON/OFF
TIME OF DAY
7 6 5 4
HEAVY DUTY
A
M
1
2•
1 1
•1
0
•9
•8
•7
•6
•5
•4•3•2•1•
1
2•1
1•1
0
•9
•8
•7
•6
•5
•4
•3
•2
•1
•
AM
P
M
PM
ON/OFF
TIME OF DAY
7 6 5 4
HEAVY DUTY
A
M
1
2•
1 1
•1
0
•9
•8
•7
•6
•5
•4•3•2•1•
1
2•1
1•1
0
•9
•8
•7
•6
•5
•4
•3
•2
•1
•
AM
P
M
PM
Remove back plate screws
to access battery compartment.
Turn timer/receiver switch clockwise
one more “click’ to turn timer off.
Setup Test Button
Locate sensor up to 40 ft.
away from timer/receiver.
Loosen the locking nut to aim sensor
as needed. Tighten nut to secure at
the desired angle.
Batteries not included.
Receiver/timer control
Lighting power pack timer control
Remove trippers from
power pack timer.
Fig. 1
ON/OFF
TIME
TIME
2
2
4
4
6
6
8
8
10
10
12
12
!
!
ON/OFF
TIME OF DAY
7 6 5 4
HEAVY DUTY
A
M
12
•1
1•
10
•9
•8
•7
•6
•5
•4•3•2•1•
12•1
1•1
0
•9
•8
•7
•6
•5
•4
•3
•2
•1
•
AM
P
M
PM
ON/OFF
TIME OF DAY
7 6 5 4
HEAVY DUTY
A
M
12
•1
1•
10
•9
•8
•7
•6
•5
•4•3•2•1•
12•1
1•1
0
•9
•8
•7
•6
•5
•4
•3
•2
•1
•
AM
P
M
PM
ON/OFF
TIME
TIME
2
2
4
4
6
6
8
8
1
0
1
0
12
12
AM
P
M
Rotate switches clockwise to “ON” position.
ON/OFF
TIME OF DAY
7 6 5 4
HEAVY DUTY
A
M
1
2•
1 1
•1
0
•9
•8
•7
•6
•5
•4•3•2•1•
1
2•1
1•1
0
•9
•8
•7
•6
•5
•4
•3
•2
•1
•
AM
P
M
PM
Turn timer/receiver switch
clockwise one more “click”
to turn timer off.
3 ft. minimum
(91.44 cm)
Setup Test Button
1
a
Outdoors:
Hang timer/receiver
and plug into a GFCI outdoor
electrical outlet that has a
weather resistant cover.
(see fig.1 above)
1
b
Indoors:
Hang timer/receiver
and plug into a grounded, indoor
electrical outlet.
2
Plug the light or other product
into the timer/receiver.
3
Position the trippers on the
timer/receiver at the “ON” and
“OFF” times desired.
4
Turn the timer/receiver and the
light or other product to the “ON”
position. The light, or product
should now be on.
5
Follow steps 6 thru 9 (above) to
complete the setup and testing.
IMPORTANT:
See warning
information located on the
label inside the cover lid
of the timer/receiver.
