![Intercoax ECP-8301EP Installation Manual Download Page 1](http://html1.mh-extra.com/html/intercoax/ecp-8301ep/ecp-8301ep_installation-manual_2076184001.webp)
AC/DC Adapter(12V)
Product Installation Guide
ECP-8301EP/NP
설치 가이드 /
Installation Guide
제품 설치 가이드
제품 각 부분의 명칭 / Hardware Overview
고객 지원 정보 / Customer Service
제품 적용 구성도 / Product Application
고객 지원과 관련된 자세한 정보는 웹사이트에서 확인하실 수 있습니다.
Pl
ease visit below website for more detail information.
http://www.intercoax.com
Intercoax Co., Ltd.
TEL : 031-365-3133~4
FAX : 031-365-3135
E-mail : [email protected]
10/100 Ethernet
PoE IP Camera
PoE
NVR
10/100 Ethernet
Non-PoE IP Camera
1. 별도의 IP설정이 필요없이 자동으로 카메라에 IP를 부여하는 경우(DHCP 등)를
제외하고, 카메라 제조사 설명서를 참조하여 카메라에 IP주소를 설정해 둡니다.
2. 동축케이블의 BNC커넥터를 ECP-8301EP/8301NP에 각각 연결합니다.
3. 56V 전원 어댑터를 ECP-8301EP/8301NP에 먼저 연결한 후 AC전원 콘센트에
연결합니다.
* 케이블의 종류 및 상태, PoE 카메라의 소비전력(W) 등에 따라 실제 연결 가능한
총 거리가 줄어들 수 있습니다. (7W 카메라의 경우 56V 단일 전원 공급으로
5C-HFBT 최대 1200m까지 PoE지원.)
* 별도 전원을 공급받는 IP 카메라를 설치하는 경우, PoE 스위치를 OFF로
설정합니다.
* ECP-8301EP/8301NP 두 제품은 모두 BNC커넥터를 통해 데이터와 전원을
함께 전송합니다. ECP-8301NP은 PoE 출력 기능이 지원되지 않는 제품으로,
RJ45 단자를 통해 데이터만 전송합니다. 따라서 카메라 등 연결된 장치에
별도 전원 공급이 필요합니다.
4. ECP 제품이 문제 없이 연결된 경우, PWR / BNC Join LED가 켜진 것을 확인합니다.
5. 동봉된 브라켓을 ECP-8301EP/8301NP에 먼저 부착한 후 전체 제품이 움직이지
않도록 잘 고정시킵니다.
6. 준비된 UTP케이블(랜선)을 이용하여 작동중인 NVR과 ECP-8301EP/8301NP을
먼저 연결하고, 이후 카메라와 ECP-8301EP/8301NP을 연결합니다.
7. PoE IP 카메라를 설치하는 경우, 카메라쪽 ECP-8301EP의 PoE 스위치를
ON으로 설정합니다.
[노트북 컴퓨터 등을 NVR쪽 ECP-8301EP/8301NP에 연결하여 전 구간의
통신 상태를 확인하기 위한 Ping 테스트를 권장합니다.]
8. NVR에 연결된 모니터를 통해 각 카메라의 영상이 잘 나오는 지 확인합니다.
1. Without an IP setting (i.e. DHCP) except when you automatically
give it up to the camera, set the IP address on the camera following
the camera manufacturer’s manual.
2. Connect BNC connectors of coaxial cable to each ECP-8301EP/8301NP.
3. Connect 56V DC power to ECP-8301EP/8301NP first and then to AC outlet.
* The total distance may vary with the type and condition of cables,
and power consumption of PoE camera. (For example of 7W camera,
one 56V DC power can supply up to 1200m of 5C-HFBT equivalent to RG6.)
* Both 8301EP/8301NP transmit data and power together via BNC connector.
ECP-8301NP does not Have PoE Support so that it can send data only via RJ45.
Connected device (i.e. IP camera) to ECP-8301NP needs to have extra
power supply.
4. When they are connected without any problem, PWR / BNC Join LED are on.
5. Adhere the brackets in the package to ECP-8301EP/8301NP and then fix up
the products.
6. Connect the UTP(LAN) cable between ECP-8301EP/8301NP and NVR first
and then between ECP-8301EP/8301NP and camera.
7. Turn on the PoE switch on ECP-8301EP for PoE IP camera and
if the camera is
powered by a separate power source (not powered by PoE output feature
of the ECP-8301EP), turn off the PoE switch on ECP-8301EP.
[Ping test is recommended to confirm the whole network.]
8. Check the video signal on the monitor.
구성품 / Package Contents
ECP-8301EP / 8301NP
브라켓
Bracket
설치 가이드
Installation Guide
설치 가이드
AC/DC Adapter (56V)
Coaxial Cable
Coaxial Cable
ECP-8301EP
ECP-8301EP
ECP-8301NP
AC/DC Adapter (56V)
ECP-8301NP