![Intercoax ECP-2701NP Quick Start Manual Download Page 1](http://html1.mh-extra.com/html/intercoax/ecp-2701np/ecp-2701np_quick-start-manual_2076182001.webp)
Package
ECP-2701 /
ECP-2701NP
DC Cable &
DC Terminal Block
Quick Start Guide
Hardware Overview
Right
Left
Left
BNC
커넥터
ECP-2701
ECP-2701
ECP-2701NP
ECP-2701NP
DC
전원
어댑터
상태
표시등
Join
버튼
DC OUT
스위치
RJ45
DC OUT
표시등 터미널
블럭
PoE / DC OUT
스위치
RJ45
DC OUT
표시등 터미널
블럭
Status LED indicator
DC Power Jack
Join Button
BNC connector
DC OUT LED
DC OUT LED
PoE or DC OUT
Switch
DC OUT Switch
Terminal Block
Terminal Block
Overview
This device is a High-Speed, long distance Ethernet & PoE extender
that makes possible to transmit IP data up to 2.4Km and PoE up to
1.2Km through various analog cables in different situations.
It is cost-effective and time saving solution to migrate existing analog
system to IP based system since ECP-2701 supports easy installation
utilizing the existing CCTV cable (Coax, UTP, 2wire & Etc.).
With long distance transmission feature, the device makes to
overcome 100 meters distance limitation easily and reduces the
construction cost significantly compared with fiber optic configuration.
Features
Ethernet over coax (UTP, 2-Wire) communication following
IEEE1901 Standard
Data + Power over Coax (or UTP, 2-wire)
Data distance up to 2.4Km
PoE distance up to 1.2Km
Gigabit Bandwidth
10/100/1000 Full Duplex
128bit AES network encryption
Supports Multi-connection (Daisy chain, Star, etc.)
PoE, PoE+, Extra PoE (Max. 60W output)
Î
ECP-2701NP does not support PoE output
Supports UTP, Telephone (2 Pairs), 2-Wire cable communication
(Using BTE Series)
Quality LED (Data & Power)
Plug & Play
Surge Protection
12VDC output (for Non-PoE Camera)
Quick Start Guide
[Rev.2.0]
ECP-2701 Series
Please read carefully the instruction manual before use. Depending
on the model, the image and the actual look of the product may vary.
LED Indicators
Indicator
Color
Function
BNC Join
EoC Devices connected
PWR
56VDC input connected
Quality
LINK
Good data connection
Poor data connection
PWR
Good power supply condition
Additional adapter required
Data
Flashes when data is transferred
PoE
PoE power supply status
DC OUT
DC OUT switch is ON
Installation Guide
1. Set the IP address on the camera following the instruction manual
of the camera.
Î
If the camera IP is automatically assigned (DHCP, etc.), there is no
need to set the camera IP separately.
2. Connect BNC of the coaxial cable to each
ECP-2701
.
3. Connect DC power to
ECP-2701
first and then to AC outlet.
Î
In case of 7W camera, the device supports long distance PoE
transmission up to 1200m over RG6 coaxial cable.
PoE transmission distance can be varied depending on cable type
and Camera’s power consumption(W).
Î
Please download full manual for more information about PoE
distance by various cables.
4. When they are correctly connected, PWR/BNC Join/Quality PWR
LED are on.
5. Fix up
ECP-2701
where it should be placed.
6. Connect the UTP(LAN) cable between
ECP-2701
and NVR first and
then between
ECP-2701
and camera.
Î
ECP-2701
is recommended for camera side and
ECP-2701NP
is
recommended for NVR/Switch side.
7. Turn on the PoE switch on
ECP-2701
for PoE IP camera.
Turn off(DC OUT ON) for non-PoE camera and connect DC Cable
between camera and Terminal Block on ECP-2701.
Î
ECP-2701
send data and power together via BNC connector.
Î
Mind the polarity (+/-) and tie up DC cable on the terminal block.
8. Ping test is recommended to confirm the whole network after
installation.
9. Check the video signal on the monitor.