background image

4

Interchange Brands, LLC

Pneumatic Carton Closing Staplers

Model No. SAB100-A 

& SAB150-C

DANGER

1. 

NEVER USE IN PRESENCE OF FLAMMABLE LIQUIDS OR 

COMBUSTIBLES. Never use any type of flammable gases or oxygen 

as a power source for the tool . Use filtered, lubricated, and regulated 

compressed air only .  

2. 

NEVER USE GASOLINE OR OTHER FLAMMABLE LIQUIDS TO 

CLEAN THE TOOL. Vapors in the tool may ignite by a spark and cause 

the tool to explode .  

3. 

DO NOT EXCEED maximum permissible operating pressure of the tool  

﹙114 psi / 8kg/cm

2

﹚ . 

4. 

DISCONNECT THE TOOL FROM AIR SUPPLY before cleaning, clearing 

jams, servicing, adjusting, and when not in use .  

WARNING 

5. 

OPERATORS AND OTHERS IN WORK AREA MUST 

WEAR SAFETY GLASSES WITH SIDE SHIELDS. 

Ear and head protection may be needed in some work 

environments .  

6. 

DO NOT USE A CHECK VALVE or any other fitting that allows air to 

remain in the tool . 

7. 

ALWAYS CARRY THE TOOL BY THE HANDLE ONLY. Never carry the 

tool by the hose or pull the hose to move the tool .  Do not pull the trigger 

when carrying or holding the tool . 

8. 

DO NOT PLACE YOUR HAND OR ANY PART OF YOUR BODY IN THE 

STAPLE CLINCHING AREA or adjustment window of the tool when 

connecting or disconnecting air supply .  

9. 

NEVER POINT ANY OPERATIONAL DRIVING TOOL AT YOURSELF 

OR AT ANY OTHER PERSON. 

Safety Instructions

Important Safety Instructions for 

Operating Staplers

READ ALL INSTRUCTIONS

!

Summary of Contents for SAB100-A

















Reviews: