manualshive.com logo in svg

Interactive Technologies Commander 2000, Owner'S Manual, Page: 50 / 61

Share
Download
Interactive Technologies Commander 2000 Owner'S Manual Download Page 50

50

Figure 8

. Floor Plan Example

Living
Room

Dining
Room

Basement

x

H

Hall

Bedroom

Bedroom

Living
Room

Recreation
Room

Basement

Hall

Bedroom

Bedroom

Living
Room

Dining
Room

Hall

Bedroom

Bedroom

Bedroom

Kitchen

A smoke detector should 

be  located   on  each l ev el .

Smoke detectors should

be  lo ca ted   be twe e n t he 

sl ee pin g  ar ea  a nd  the  r es t

of the family living unit.

NOTE:  Do not in stall smoke detectors where normal ambient temper atures are above

 

100°F or below 40°F. Also, do not locate detectors in front of AC/ Heat 

 

registers or other lo cations where normal air circulatio n will keep smoke

 

fr om  entering the detector.

NOTE:  Additional in format ion on household fire warning is available at nominal 

 

cost  from: The National Fire Protection Association, Batterymarch Park,

 

Quincy , MA 02269. Request Standard No. NFPA74.

 

H

x

Living
Room

Bedroom

Bedroom

Bedroom

Dining
Room

Kitchen

TV
Room

In family living units with more

than one sleepin g area, lo cate a 

smoke detector at each area.

H

NOTE:  Ceiling-mounted smoke detectors should be lo cated in the center of the room

 

or hall, or not less than 4 inches fr om  the wall. When the detector  is mounted

 

on the wall, the top of the detector should be 4 to 12 inches from the ceiling.

Required smoke detector

He at detec tor

Indicates smoke detector is optional if door is not provid ed between

basement and recreation rooms.

8557144a

Technical Manuals Online! - http://www.tech-man.com

Summary of Contents for Commander 2000






























































Reviews:

No comments