Intellinet 561587 User Manual Download

Page: 21 / 121

48-Port Gigabit Ethernet PoE+ Managed Switch with Four 10G SFP+ Uplinks

User Manual

Connecting the Switch

5.1

Connect the Computer (NIC) to the Switch

Use standard Cat5/5e Ethernet cable (UTP/STP) to connect the Switch to end nodes as described

below. Switch ports will automatically adjust to the characteristics (MDI/MDI-X, speed, duplex)
of the device to which is connected.

Sample connection.

Figure 5-1 Connect PC to Switch

5.2

Switch connections to Powered Devices

This PoE Switch can supply power to compatible devices. Each port offers a maximum output up

to 30 W to power an internet phone, network camera, wireless access point or other device. Use

appropriate cable to directly connect the Switch's PoE port to the PD port.

Only PoE devices support the PoE function.

Summary of Contents for 561587


























































































































Search results

Summary of Contents for 561587

Reviews:

Related manuals for 561587

Brands by name

Popular brands

Intellinet 561587, User Manual

Search results

Summary of Contents for 561587

Reviews:

Related manuals for 561587

Brands by name

Popular brands