Specifications
Specifications subject to change without notice.
Maximum Distance*
2,200 feet
Maximum Video Input
1.1 Vp-p
Bandwidth (video)
DC to 8 MHz
Impedance (video)
75 ohms
Insertion Loss
Less than 2 dB per pair over the frequency range from
DC to 8 MHz
Return Loss
Greater than 15 dB over the frequency range from DC to
8 MHz
Common Mode Rejection
Greater than 40 dB @ 8 MHz
Unshielded Twisted Pair
Maximum capacitance: 20 pf/foot
Cabling Specifications
Impedance: 100 ohms @ 1 MHz
(24 gauge or lower solid
Attenuation: 6.6 dB/1000 ft. @ 1 MHz
copper)
Cat 3, Cat 5, Cat 5e, Cat 6, Cat 7 compatible
Connectors
One (1) female RCA to one (1) RJ45
Pinout
7 & 8, pair 4
Temperature
Operating: 32 to 131 F (0 to 55 C)
Storage: -4 to 185 F (-20 to 85 C)
Humidity: up to 95%
Enclosure
Front: standard decora-style wallplate
Rear: metal
Dimensions
4.0” x 1.4” x 1.7”
Ordering Information
AVO-V1-WP
: single AVO-V1-WP balun in bulk
packaging
Warranty
2 years
*
Distances and picture quality may be affected by cable grade, cable quality, source and
destination equipment, RF and electrical interference, and cable patches. Intelix specifications are
based on straight-through cabling with standard-grade Cat 5.
Contact Information
Intelix
2222 Pleasant View Road
Middleton, WI 53562
Toll-free: 866-4-MATMIX
Phone: 608-831-0880
Fax: 608-831-1833
www.intelix.com
Intelix AVO-V1-WP Video Balun
Ins
Ins
Ins
Ins
Inst
tt
ttallation Manual
allation Manual
allation Manual
allation Manual
allation Manual
The Intelix AVO-V1-WP wallplate balun transmits one composite video signal over stan-
dard structured cabling, such as Cat 5. Used in pairs or with a rack-mountable Intelix AVO-
V1 balun, AVO-V1-WP baluns replace bulky coaxial video cable and transmit a video
signal up to 2,200 feet.
The Intelix
Avo
Cat
Series of baluns is the ideal solution for sending video over structured
cabling.
When signal quality matters, choose Intelix.
To install an AVO-V1-WP balun, perform the following steps:
1. Turn off power and disconnect the video equipment by following the manufacturer’s
instructions.
2. Run your unshielded twisted pair cabling, such as Cat 5.
3. The AVO-V1-WP
balun works in pairs or with other compatible Intelix baluns,
such as the AVO-V1 rack-mountable balun. Connect the AVO-V1-WP
balun to the
source device with a composite video cable.
4. Connect a second AVO-V1-WP or compatible balun to the destination device.
5. Connect a structured cable, such as Cat 5, to each RJ45 connector of the baluns.
Verify the pinout on the connector conforms to the EIA/TIA 568A or 568B
pattern standards.
6. Power-on the video equipment and check the picture quality. The video should be
clear and sharp within the maximum specified distances.
Installation
Caution:
Do not mount the balun over equipment ventilation openings. Covering the
openings may cause the equipment to overheat.
Avo
Cat
Series
Caution:
Do not attempt to disassemple or alter the balun housing. There are
no user-serviceable parts inside the AVO-V1-WP. Modifying the unit
will void your warranty.
Caution:
Do not connect the AVO-V1-WP to a telecommunication outlet
wired to unrelated equipment. Making such a connection may damage
the equipment and/or balun. Please ensure all wiring is “straight-
through.”
