Intel Xeon E5-2400 Page 46 Thermal/Mechanical Design Manual Download | Manualshive

Page: 46 / 100

background image

Quality and Reliability Requirements

46

Intel® Xeon® Processor E5-2400 Product Family

Thermal/Mechanical Design Guide

6.2.3

Recommended BIOS/Processor/Memory Test Procedures

This test is to ensure proper operation of the product before and after environmental
stresses, with the thermal mechanical enabling components assembled. The test shall
be conducted on a fully operational baseboard that has not been exposed to any
battery of tests prior to the test being considered.

The testing setup should include the following components, properly assembled and/or
connected:

• Appropriate system baseboard.
• Processor and memory.
• All enabling components, including socket and thermal solution parts.

The pass criterion is that the system under test shall successfully complete the
checking of BIOS, basic processor functions and memory, without any errors.

6.3

Material and Recycling Requirements

Material shall be resistant to fungal growth. Examples of non-resistant materials
include cellulose materials, animal and vegetable based adhesives, grease, oils, and
many hydrocarbons. Synthetic materials such as PVC formulations, certain
polyurethane compositions (for example, polyester and some polyethers), plastics
which contain organic fillers of laminating materials, paints, and varnishes also are
susceptible to fungal growth. If materials are not fungal growth resistant, then MIL-
STD-810E, Method 508.4 must be performed to determine material performance.

Any plastic component exceeding 25 gm should be recyclable per the European Blue
Angel recycling standards.

The following definitions apply to the use of the terms lead-free, Pb-free, and RoHS
compliant.

Lead-free and Pb-free:

Lead has not been intentionally added, but lead may still

exist as an impurity below 1000 ppm.

RoHS compliant:

Lead and other materials banned in RoHS Directive are either

(1) below all applicable substance thresholds as proposed by the EU or (2) an
approved/pending exemption applies.

Note:

RoHS implementation details are not fully defined and may change.

§

«
...
44
45
46
47
48
...
»

Summary of Contents for Xeon E5-2400





































































































Reviews:

No comments

Related manuals for Xeon E5-2400

Brand: ebm-papst Pages: 16

Brand: Opvimus Pages: 12

Brand: Acces I/O products Pages: 5

SINUS H PROFInet

Brand: Enertronica Santerno Pages: 34

Brand: Ubiquiti Pages: 21

Brand: Cisco MERAKI Pages: 4

BROADCAST POLLING FRAD BPF-14 BU

Brand: DCB Pages: 28

Brand: Laser Pages: 4

Brand: ExtraHop Pages: 3

Brand: IBM Pages: 168

Brand: Alphacool Pages: 9

BPN-SAS3-LB16A-N10

Brand: Supermicro Pages: 11

Brand: WIN Enterprises Pages: 25

CU8210-D001-0200

Brand: Beckhoff Pages: 25

EK-UNI Holder D5 V3

Brand: ekwb Pages: 2

IQ Switch ProxSense RS100

Brand: Azoteq Pages: 9

Brand: BenQ Pages: 38

UEZGUI-4357-70WVN

Brand: FDI Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands