Intel SR2612UR - Server System - 0 MB RAM Service Manual Download Page 57 | Manualshive

Page: 57 / 162

background image

Intel

®

Server System SR2612UR Service Guide

43

Figure 35. Position the DVD Unit

9. Slide the DVD / tray assembly back into the enclosure and anchor it using the screw

that was removed in Step 7.

10. Using the slimline cable shipped with the system, connect the power end of

slimline cable to the power cable located in the enclosure and the SATA end of
slimline cable to the CPU server board. If 2.5-inch drives are installed, connect the
SATA cable to the SATA2 connector.

Figure 36. Routing the Cable From the DVD Unit to the Server Board

11. Reinstall the top cover and tighten the captive screw.

12. Reinstall the power cord(s).

Replacing a Fan

You should replace a defective fan as soon as possible to maintain proper cooling in the
enclosure. Complete the following steps to remove and install a fan in the Intel

®

Server

System SR2612UR.

«
...
55
56
57
58
59
...
»

Summary of Contents for SR2612UR - Server System - 0 MB RAM



































































































































































Reviews:

No comments

Related manuals for SR2612UR - Server System - 0 MB RAM

Brand: IBM Pages: 151

NetVista N2800e

Brand: IBM Pages: 82

NovaScale T820 F2

Brand: Bull Pages: 34

Brand: IBM Pages: 194

Eserver 345 Series

Brand: IBM Pages: 70

Brand: Kyocera Pages: 207

Brand: Huawei Pages: 2

Brand: Huawei Pages: 52

Brand: Huawei Pages: 122

Brand: Huawei Pages: 131

UPS5000-E-****-FM series

Brand: Huawei Pages: 261

IP-DECT SERVER 6500

Brand: SpectraLink Pages: 126

Brand: QNAP Pages: 49

Xtreme PC NG6452

Brand: Chip PC Pages: 4

SocketEthernetIP EN60601

Brand: Multitech Pages: 2

Brand: Meinberg Pages: 55

Brand: 7th Sense Pages: 24

EtherneTV-NXG 1

Brand: VBrick Systems Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands