Intel S3000AH User Manual Download Page 33 | Manualshive

Page: 33 / 74

background image

Intel

®

Server Board S3000AH User’s Guide

15

Optional Hardware

Hard Disk Drives

The Intel

®

Server Board S3000AH provides four SATA ports and one IDE connection.

The four SATA ports are near the front left side of the server board. The IDE connection
supports one or two ATA-100 devices. IDE devices can be connected to the standard IDE
connector located near the SATA ports.

See the documentation included with your server chassis for additional drive information
and drive installation instructions.

«
...
31
32
33
34
35
...
»

Summary of Contents for S3000AH











































































Reviews:

No comments

Related manuals for S3000AH

Brand: MRV Communications Pages: 65

Brand: SMART-AVI Pages: 43

Brand: Fundex Games Pages: 1

Brand: Fundex Games Pages: 1

Brand: Fundex Games Pages: 3

Brand: Fundex Games Pages: 2

Brand: Planet Pages: 87

Brand: Sugon Pages: 155

Brand: Inspur Pages: 196

Brand: Check Point Pages: 53

Brand: Ampair Pages: 26

Brand: Gigabyte Pages: 163

Brand: Inspur Pages: 68

Brand: Oracle Pages: 168

Brand: Digitus Pages: 8

Brand: Gigabyte Pages: 166

Brand: dallmeier Pages: 16

SMAVIA IPS 10000

Brand: dallmeier Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands