Intel P4000M Service Manual Download Page 97

Page: 97 / 111

Technical Reference

Intel

Server Chassis P4000M Service Guide

Technical Reference

Power Supply Specification

The power supply specifications for your Intel

Server Chassis P4000M family depend upon the

configuration of chassis you purchased. Below power supply configurations are available:



460-W hotswap power supply



550-W fixed power supply



750-W hotswap power supply



1200-W hotswap power supply

460-W Hotswap Power Supply Input Voltage



100-127V at 50/60 Hz; 10A max.



200-240V at 50/60 Hz; 10A max.

460-W Hotswap Power Supply Output Voltages

The following table defines the minimum power and current ratings.

The power supply must meet

both static and dynamic voltage regulation requirements for all conditions.

Table 3. 460-W Power Supply Output Voltages

Parameter

Tolerance

MIN

NOM

MAX

UNITS

+12V

- 5%/+5%

+11.40

+12.00

+12.60

rms

+12V stby

- 5%/+5%

+11.40

+12.00

+12.60

rms

550-W Single Power Supply Input Voltage



100-127V at 50/60 Hz; 10A max.



200-240V at 50/60 Hz; 10A max.

550-W Single Power Supply Output Voltages

The following table defines the minimum power and current ratings.

The power supply must meet

both static and dynamic voltage regulation requirements for all conditions.

Summary of Contents for P4000M
















































































































Search results

Summary of Contents for P4000M

Reviews:

Related manuals for P4000M

Brands by name

Popular brands

Intel P4000M, Service Manual

Search results

Summary of Contents for P4000M

Reviews:

Related manuals for P4000M

Brands by name

Popular brands