Intel P4000M Service Manual Download Page 95 | Manualshive

Page: 95 / 111

background image

Hardware Installations and Upgrades

Intel

®

Server Chassis P4000M Service Guide

81

Intel

®

Remote Management Module 4

The Intel

®

Remote Management Module 4 plugs into a dedicated connector on the server board

and provides additional server management functionality to the server board.

This module provides a dedicated web server for viewing server information and remote control of
the system. It also provides Remote KVM Redirection and USB Media Redirection allowing USB
devices attached to the remote system to be used on the managed server.

Intel

®

Server Chassis P4000M family provide two Intel

®

Remote Management Module 4

knockout. For instructions on installing the Intel

®

Remote Management Module 4, see

Intel

®

Remote Management Module 4 User Guide

.

Figure 131. RMM4 knockout

«
...
93
94
95
96
97
...
»

Summary of Contents for P4000M
















































































































Reviews:

No comments

Related manuals for P4000M

eServer BladeCenter HS20Type 8832

Brand: IBM Pages: 158

SX-2000A Series

Brand: GDC Pages: 185

NSLU2 - Network Storage Link NAS Server

Brand: Linksys Pages: 64

SuperServer 6026TT-HIBQF

Brand: Supero Pages: 112

Brand: Supermicro Pages: 113

HP ProLiant DL360P Gen8

Brand: Honeywell Pages: 67

Brand: SpectraLink Pages: 31

Compaq AlphaServer DS10

Brand: HP Pages: 43

Cluster Platform Hardware Kits v2010

Brand: HP Pages: 12

Brand: HP Pages: 12

hpe proliant dl20 gen9

Brand: HP Pages: 131

Cisco MDS 8/12c

Brand: HP Pages: 44

Cluster Platform

Brand: HP Pages: 74

Cisco MDS 8/24c

Brand: HP Pages: 44

Cluster Platform

Brand: HP Pages: 88

HPE ProLiant DL180 Gen10

Brand: HP Pages: 157

HPE ProLiant DX360 Gen10

Brand: HP Pages: 187

Apollo 2000 System

Brand: HP Pages: 178

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands