Intel P4000M Service Manual Download Page 86

Page: 86 / 111

Hardware Installations and Upgrades

Intel

Server Chassis P4000M Service Guide

Figure 117. Installing the Chassis Feet

7. Put chassis in the upright position.

8. Reconnect all peripheral devices and the AC power cable to the server. Power up the server.

Removing and Installing the Front Panel Tray

CAUTION

The front panel is NOT hot swappable. Before removing or replacing the control panel, you must

first take the server out of service, turn off all peripheral devices connected to the system, turn off

the system by pressing the power button, and unplug the AC power cord from the system or wall

outlet.

Removing the Front Control Panel Tray

1. Observe the safety and ESD precautions at the beginning of this book.

2. Power down the server and unplug all peripheral devices and the AC power cable.

3. Remove the chassis cover. For instructions, see “Removing the Chassis Cover”.

4. Remove the front bezel if it is installed. For instructions, see “Removing the Front Bezel”.

5. Remove the air duct if it is installed.

6. Disconnect the front panel cable, USB cable from the server board.

Summary of Contents for P4000M
















































































































Search results

Summary of Contents for P4000M

Reviews:

Related manuals for P4000M

Brands by name

Popular brands

Intel P4000M, Service Manual

Search results

Summary of Contents for P4000M

Reviews:

Related manuals for P4000M

Brands by name

Popular brands