Intel P4000M Service Manual Download Page 35

Page: 35 / 111

Hardware Installations and Upgrades

Intel

Server Chassis P4000M Service Guide

Removing the Airduct

1. Observe the safety and ESD precautions at the beginning of this book.

2. Power down the server and unplug all peripheral devices and the AC power cable.

3. Remove the chassis cover. For instructions, see “Removing the Chassis Cover”.

4. Remove the airduct.

Replacing the Fixed Fan

NOTE

Please pay attention to the fan cable connector color. The fan with blue connector should be installed in

fan 2 bracket and the fan with white connector should be installed in fan 1 bracket. The fan numbering is

inscribed on the chassis.

This procedure applies only to the Intel

Server Chassis P4000M family with fixed fan configuration.

Removing the Fixed Fan

1. Observe the safety and ESD precautions at the beginning of this book.

2. Power down the server and unplug all peripheral devices and the AC power cable.

3. Remove the chassis cover. For instructions, see “Removing the Chassis Cover”.

4. Remove the air duct if the air duct is installed. For instructions, see “Removing the Airduct”.

5. Disconnect the appropriate fan power cable from the server board (see letter

Figure 32. Disconnecting the fan power cable from the server board

Summary of Contents for P4000M
















































































































Search results

Summary of Contents for P4000M

Reviews:

Related manuals for P4000M

Brands by name

Popular brands

Intel P4000M, Service Manual

Search results

Summary of Contents for P4000M

Reviews:

Related manuals for P4000M

Brands by name

Popular brands