Intel M50CYP2UR Series System Integration And Service Manual Download Page 96

Page: 96 / 162

Intel® Server System M50CYP2UR Family System Integration and Service Guide

6.3

System Fan Assembly Replacement

Required Tools and Supplies

•

Anti-static wrist strap and conductive workbench pad (recommended)

System fan assembly removal is required when routing cables inside the chassis from back-to-front or front-
to-back, or when server board replacement is necessary.

Note:

This section provides the steps to remove or install the system fan as an entire module. Individual fans

can also be replaced without removing the entire system fan assembly. See

Section 6.4

for replacing

individual fans.

Figure 119. System Fan Assembly Removal

Ensure the system power is off and disconnect the power cable(s).

Remove the system top cover (see

Section 6.1.1

Remove the air duct (see

Section 6.2.1

Lift the latches on both sides of the system fan upward to unlock (see Letter A).

Grasp each end of the fan module and lift the entire module straight up (see Letter B).

Carefully place the fan module component side down onto a flat surface.

Note:

Do NOT rest the fan module on the fan connectors on the bottom side of the fan module. Doing

so may damage the connectors.

Summary of Contents for M50CYP2UR Series



































































































































































Search results

Summary of Contents for M50CYP2UR Series

Reviews:

Related manuals for M50CYP2UR Series

Brands by name

Popular brands

Intel M50CYP2UR Series, System Integration And Service Manual

Search results

Summary of Contents for M50CYP2UR Series

Reviews:

Related manuals for M50CYP2UR Series

Brands by name

Popular brands