Intel M50CYP2UR Series System Integration And Service Manual Download Page 56

Page: 56 / 162

Intel® Server System M50CYP2UR Family System Integration and Service Guide

3.4.6

3.5” Drive

Carrier Installation

Figure 58

. 3.5”

Drive Carrier Installation

Note:

The 3.5” drive

carrier must be completely removed from the chassis to install a drive into the drive

carrier.

Align the drive assembly (drive and drive carrier) with the open drive bay.

With the lever in the open position, insert the drive assembly into the drive bay (see Letter A).

Push forward until the drive contacts with the backplane.

Complete the drive installation by closing the drive assembly lever until it locks into place (see Letter B).

3.4.7

3.5

”

Drive Carrier Removal

Figure 59. 3

.5”

Drive Carrier Removal

Press the button on the drive extraction/insertion lever to release the drive carrier from the drive bay (see
Letter A).

Using the lever, pull the drive carrier from the drive bay, all the way out (see Letter B).

Summary of Contents for M50CYP2UR Series



































































































































































Search results

Summary of Contents for M50CYP2UR Series

Reviews:

Related manuals for M50CYP2UR Series

Brands by name

Popular brands

Intel M50CYP2UR Series, System Integration And Service Manual

Search results

Summary of Contents for M50CYP2UR Series

Reviews:

Related manuals for M50CYP2UR Series

Brands by name

Popular brands