Intel M50CYP2UR Series System Integration And Service Manual Download Page 53

Page: 53 / 162

Intel® Server System M50CYP2UR Family System Integration and Service Guide

3.4.3

2.5”

SSD Drive / Drive Blank Removal

The 2.5” drive

mounting rails in the system are not removable. They slide out so that the storage drives can

be installed or removed. When sliding out a drive mounting rail from the system, only pull it as much as it
allows without forcing it.

Figure 52.

2.5”

Drive Removal

Press the button on the drive extraction lever to release it (see Letter A).

Using the lever, pull the drive mounting rail halfway out of the drive bay (see Letter B).

Remove the drive (or drive blank) from the drive mounting rail (see Letter C).

3.4.4

3.5”

HDD Drive Assembly

Drive Blank Removal

Drive Removal

Figure 53. 3.

5”

Drive Carrier Assembly

–

Drive Blank / Drive Removal

Hold the carrier assembly top side down in your right hand.

Using your left hand, gently rotate the bottom edge of the left rail upwards (see Letter A) while at the
same time pushing the drive or drive blank down away from the carrier (see Letter B).

Summary of Contents for M50CYP2UR Series



































































































































































Search results

Summary of Contents for M50CYP2UR Series

Reviews:

Related manuals for M50CYP2UR Series

Brands by name

Popular brands

Intel M50CYP2UR Series, System Integration And Service Manual

Search results

Summary of Contents for M50CYP2UR Series

Reviews:

Related manuals for M50CYP2UR Series

Brands by name

Popular brands