Intel M50CYP2UR Series System Integration And Service Manual Download Page 38

Page: 38 / 162

Intel® Server System M50CYP2UR Family System Integration and Service Guide

Figure 27. System Top Cover Removal

For each top cover panel:
1.

While pushing down on both the left and right buttons of the given top panel (see Letter A), slide the top
cover panel towards the front (front panel) or back (back panel) of the chassis (see Letter B).

Carefully lift the top cover panel up and away from the chassis.

Note:

Each top cover panel can slide along the chassis base for 10 mm and then needs to be lifted.

3.1.2

System Cover Installation

Figure 28. System Top Cover Installation

For each top cover panel:
1.

Carefully align and set the top cover panel on top of the chassis. Then, slide it inwards until it locks into
place (see Letter A).

Shipping Note:

When transporting the server system, Intel recommends installing the four top cover screws

before shipping.

Summary of Contents for M50CYP2UR Series



































































































































































Search results

Summary of Contents for M50CYP2UR Series

Reviews:

Related manuals for M50CYP2UR Series

Brands by name

Popular brands

Intel M50CYP2UR Series, System Integration And Service Manual

Search results

Summary of Contents for M50CYP2UR Series

Reviews:

Related manuals for M50CYP2UR Series

Brands by name

Popular brands