Intel IXP45X Developer'S Manual Download Page 57

Page: 57 / 958

Intel

IXP45X and Intel

IXP46X Product Line of Network Processors

August 2006

Developer’s Manual

Reference Number: 306262-004US

Functional Overview—Intel

IXP45X and Intel

IXP46X Product Line of Network Processors

2.1.12

Internal Bus Performance Monitoring Unit (IBPMU)

The IXP45X/IXP46X network processors consist of a performance monitoring unit that

may be used to capture predefined events within the system outside of the Intel XScale

processor. These features aid in measuring and monitoring various system parameters

that contribute to the overall performance of the processor.

The Performance Monitoring (PMON) facility provided comprises:

• Eight Programmable Event Counters (PECx)
• Previous Master/Slave Register
• Event Selection Multiplexor

The programmable event counters are 27 bits wide. Each counter may be programmed

to observe one event from a defined set of events. An event consists of a set of

parameters which define a start condition and a stop condition.

The monitored events are selected by programming the Event Select Registers (ESR).

2.1.13

Interrupt Controller

The IXP45X/IXP46X network processors consist of up to 64 interrupt sources to allow

an extension of the Intel XScale processor’s FIQ and IRQ interrupt sources. These

sources can originate from some external GPIO pins, internal peripheral interfaces, or

internal logic.

The interrupt controller can configure each interrupt source as an FIQ, IRQ, or disabled.

The interrupt sources tied to Interrupt 0 to 7 can be prioritized. The remaining

interrupts are prioritized in ascending order. For example, Interrupt 8 has a higher

priority than 9, 9 has a higher priority than 10, and 30 has a higher priority that 31.

An additional level of priority can be set for interrupts 32 through 63. This priority

setting gives any interrupt between 32 through 63 priority over interrupts 0 through

31.

Table 4.

GPIO Alternate Function Table

GPIO Pin Number

Alternate Function

External USB 1.1 Device Clock input

External USB 2.0 Host Clock input

(Reserved)

Auxiliary IEEE1588 Master Snapshot input

Auxiliary IEEE1588 Slave Snapshot input

9:13

(Reserved)

Output Clock 14

Output Clock 15

Summary of Contents for IXP45X































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IXP45X

Reviews:

Brands by name

Popular brands

Intel IXP45X, Developer'S Manual

Search results

Summary of Contents for IXP45X

Reviews:

Brands by name

Popular brands