manualshive.com logo in svg

Intel IXP45X, Developer'S Manual

Share
Download
Intel IXP45X Developer'S Manual Download Page 400

Intel

®

 IXP45X and Intel

®

 IXP46X Product Line of Network Processors—USB 2.0 Host Controller

Intel

®

 IXP45X and Intel

®

 IXP46X Product Line of Network Processors

Developer’s Manual

August 2006

400

Order Number: 306262-004US

9.13.5.1

Next qTD Pointer

The first DWord of an element transfer descriptor is a pointer to another transfer 

element descriptor.

9.13.5.2

Alternate Next qTD Pointer

The second DWord of a queue element transfer descriptor is used to support hardware-

only advance of the data stream to the next client buffer on short packet. To be more 

explicit the host controller will always use this pointer when the current qTD is retired 

due to short packet.

9.13.5.3

qTD Token

The third DWord of a queue element transfer descriptor contains most of the 

information the host controller requires to execute a USB transaction (the remaining 

endpoint-addressing information is specified in the queue head).

Note:

The field descriptions forward reference fields defined in the queue head. Where 

necessary, these forward references are preceded with a QH notation.

Table 156.

qTD Next Element Transfer Pointer (DWord 0)

Bit

Description

31:5

Next Transfer Element Pointer. This field contains the physical memory address of 

the next qTD to be processed. The field corresponds to memory address signals[31:5], 

respectively.

4:1

(Reserved). These bits are reserved and their value has no effect on operation.

0

Terminate (T).
0 = Pointer is valid (points to a valid Transfer Element Descriptor).

1 = pointer is invalid.
This bit indicates to the Host Controller that there are no more valid entries in the 

queue.

Table 157.

qTD Alternate Next Element Transfer Pointer (DWord 1)

Bit

Description

31:5

Alternate Next Transfer Element Pointer. This field contains the physical memory address 

of the next qTD to be processed in the event that the current qTD execution encounters a 

short packet (for an IN transaction). The field corresponds to memory address signals [31:5], 

respectively.

4:1

(Reserved). These bits are reserved and their value has no effect on operation.

0

Terminate (T). 
0 = Pointer is valid (points to a valid Transfer Element Descriptor).

1 = pointer is invalid.
This bit indicates to the Host Controller that there are no more valid entries in the queue.

Summary of Contents for IXP45X































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands