manualshive.com logo in svg

Intel IXP45X, Developer'S Manual

Share
Download
Intel IXP45X Developer'S Manual Download Page 398

Intel

®

 IXP45X and Intel

®

 IXP46X Product Line of Network Processors—USB 2.0 Host Controller

Intel

®

 IXP45X and Intel

®

 IXP46X Product Line of Network Processors

Developer’s Manual

August 2006

398

Order Number: 306262-004US

9.13.4.4

siTD Buffer Pointer List (Plus)

DWords 4 and 5 are the data buffer page pointers for the transfer. This structure 

supports one physical page cross. The most significant 20 bits of each DWord in this 

section are the 4K (page) aligned buffer pointers. The least significant 12 bits of each 

DWord are used as additional transfer state.

9.13.4.5

siTD Back Link Pointer

DWord 6 of a siTD is simply another schedule link pointer. This pointer is always zero, 

or references a siTD. This pointer cannot reference any other schedule data structure. 

2

Missed Micro-Frame. The host controller detected that a host-induced hold- off caused the host 

controller to miss a required complete-split transaction.

1

Split Transaction State (SplitXstate). The bit encodings are:
Value Meaning
00b Do Start Split. This value directs the host    controller to issue a Start split transaction to   the 

endpoint when a match is encountered in   the S-mask.
01b Do Complete Split. This value directs the    host controller to issue a Complete split    

transaction to the endpoint when a match is encountered in the C-mask.

0

(Reserved). Bit reserved for future use and should be zero.

Table 153.

siTD Transfer Status and Control (Sheet 2 of 2)

Bit

Description

Table 154.

Buffer Page Pointer List (Plus)

Bit

Description

31:12

Buffer Pointer List. Bits [31:12] of DWords 4 and 5 are 4K paged aligned, physical 

memory addresses. These bits correspond to physical address bits [31:12] respectively. 

The lower 12 bits in each pointer are defined and used as specified below. The field P 

specifies the current active pointer

11:0

Page 0:
Current Offset. The 12 least significant bits of the Page 0 pointer is the current byte offset 

for the current page pointer (as selected with the page indicator bit (P field)). The host 

controller is not required to write this field back when the siTD is retired (Active bit 

transitioned from a one to a zero). The least significant bits of Page 1 pointer is split into 

three sub-fields
Page 1:

11:5

(Reserved).

4:3

Transaction position (TP). This field is used with T-count to determine 

whether to send all, first, middle, or last with each outbound transaction 

payload. System software must initialize this field with the appropriate 

starting value. The host controller must correctly manage this state 

during the lifetime of the transfer. The bit encodings are:
Value

Meaning

00b

All. The entire full-speed transaction data payload is in this 

transaction (that is, less than or equal to 188 bytes).
01b

Begin. This is the first data payload for a full-speed transaction 

that is greater than 188 bytes.
10B

Mid. This is the middle payload for a full-speed OUT transaction 

that is larger than 188 bytes.
11b

End. This is the last payload for a full-speed OUT transaction 

that was larger than 188 bytes.

2:0

Transaction count (T-Count). Software initializes this field with the 

number of OUT start-splits this transfer requires. Any value larger than 6 

is undefined.

Summary of Contents for IXP45X































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands