manualshive.com logo in svg

Intel ITANIUM ARCHITECTURE, Manual

Share
Download
Intel ITANIUM ARCHITECTURE Manual Download Page 81

4:74

Volume 4: Base IA-32 Instruction Reference

CMPXCHG—Compare and Exchange

Description

Compares the value in the AL, AX, or EAX register (depending on the size of the 
operand) with the first operand (destination operand). If the two values are equal, the 
second operand (source operand) is loaded into the destination operand. Otherwise, 
the destination operand is loaded into the AL, AX, or EAX register.

This instruction can be used with a LOCK prefix to allow the instruction to be executed 
atomically. To simplify the interface to the processor’s bus, the destination operand 
receives a write cycle without regard to the result of the comparison. The destination 
operand is written back if the comparison fails; otherwise, the source operand is written 
into the destination. (The processor never produces a locked read without also 
producing a locked write.)

Operation

(* accumulator = AL, AX, or EAX, depending on whether *)
(* a byte, word, or doubleword comparison is being performed*)

IF Itanium System Environment AND External_Atomic_Lock_Required AND DCR.lc

THEN IA-32_Intercept(LOCK,CMPXCHG);

IF accumulator = DEST

THEN

ZF 

 1

DEST 

 SRC

ELSE

ZF 

 0

accumulator 

 DEST

FI;

Flags Affected

The ZF flag is set if the values in the destination operand and register AL, AX, or EAX 
are; otherwise it is cleared. The CF, PF, AF, SF, and OF flags are set according to the 
results of the comparison operation.

Opcode

Instruction

Description

0F B0/

r

CMPXCHG 

r/m8,r8

Compare AL with 

r/m8

. If equal, ZF is set and 

r8

 is loaded into 

r/m8

. Else, clear ZF and load 

r/m8

 into AL.

0F B1/

r

CMPXCHG 

r/m16,r16

Compare AX with 

r/m16

. If equal, ZF is set and 

r16

 is loaded 

into 

r/m16

. Else, clear ZF and load 

r/m16

 into AL

0F B1/

r

CMPXCHG 

r/m32,r32

Compare EAX with 

r/m32

. If equal, ZF is set and 

r32

 is loaded 

into 

r/m32

. Else, clear ZF and load 

r/m32

 into AL

Summary of Contents for ITANIUM ARCHITECTURE





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands