manualshive.com logo in svg

Intel ITANIUM ARCHITECTURE, Manual

Share
Download
Intel ITANIUM ARCHITECTURE Manual Download Page 210

Volume 4: Base IA-32 Instruction Reference

4:203

HLT—Halt

Description

Stops instruction execution and places the processor in a HALT state. An enabled 
interrupt, NMI, or a reset will resume execution. If an interrupt (including NMI) is used 
to resume execution after a HLT instruction, the saved instruction pointer (CS:EIP) 
points to the instruction following the HLT instruction.

The HLT instruction is a privileged instruction. When the processor is running in 
protected or virtual 8086 mode, the privilege level of a program or procedure must to 0 
to execute the HLT instruction.

Operation

IF Itanium System Environment THEN IA-32_Intercept(INST,HALT);

Enter Halt state;

Flags Affected

None.

Additional Itanium System Environment Exceptions

IA-32_Intercept

Mandatory Instruction Intercept.

Protected Mode Exceptions

#GP(0)

If the current privilege level is not 0.

Real Address Mode Exceptions

None.

Virtual 8086 Mode Exceptions

#GP(0)

If the current privilege level is not 0.

Opcode

Instruction

Description

F4

HLT

Halt

Summary of Contents for ITANIUM ARCHITECTURE





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands