manualshive.com logo in svg

Intel Edison Kit for Arduino, Hardware Manual, Page: 16 / 32

Share
Download
Intel Edison Kit for Arduino Hardware Manual Download Page 16

 

Shield pin configuration 

 
 

Figure 4 

PWM swizzler on the Intel® Edison kit for Arduino* 

 

3.3

 

Intel® Edison kit for Arduino* analog inputs 

The analog inputs are fed to an ADS7951 A/D converter. This device has the following features: 

•

 

20 MHz clock rate 

•

 

12-bit A/D conversion 

•

 

1 MHz sample rate 

•

 

70 dB signal to noise ratio 

•

 

0 to 2.5 V or 0 to 5 V input range (select either AREF or IOREF via jumper J8 onboard) 

The analog inputs are multiplexed with digital I/O using SN74LVC2G53 analog switches. These switches isolate the 
digital I/O from the analog input to prevent crosstalk. The SN74LVC2G53 also has an inhibit pin that places the I/O 
in a tristate condition. The switch also has low on state resistance of 15 ohm at 4.5 V VCC.  

3.4

 

Intel® Edison kit for Arduino* signal pullup resistors 

The analog and digital pins can be configured to have an external pull-up resistor connected. The pullup value is 
fixed at 47 kohm.  

3.5

 

Intel® Edison kit for Arduino* USB interface 

The Intel® Edison compute module has a single USB 2.0 interface. This interface is the primary method for 
downloading code. The Intel® Edison compute module is designed to support OTG, using the ID signal. Circuitry on 
the Intel® Edison kit for Arduino* board uses a USB multiplexer, and an external switch to configure the USB 
interface as a host port or device port. SW1 is a slider switch which selects between host mode and device mode. 
When the slider is switched towards the USB standard size Type A connector, the Intel® Edison compute module 
will go to host mode. When the switch is towards the micro USB Type B connector, the Intel® Edison compute 
module will go to device mode.  

Note:

 

USB host mode always requires use of an external power adapter.  

Intel® Edison Kit for Arduino*  

 

 

Hardware Guide 

 

December 2014 

16 

 

 

Document Number: 331191-004 

Summary of Contents for Edison Kit for Arduino

































Reviews:

No comments