Intel CELERON PROCESSOR P4505 - ADDENDUM Page 133 Datasheet Download

Page: 133 / 139

Intel

Core

i7-660UE, i7-620LE/UE, i7-610E, i5-520E, i3-330E and Intel

Celeron

Processor P4505, U3405 Series

August 2010

Datasheet Addendum

Document Number: 323178-003

133

Processor Configuration Registers

6.2.48

PEGLC - PCI Express-G Legacy Control

B/D/F/Type:

0/6/0/PCI

Address Offset:

EC-EFh

Default Value:

00000000h

Access:

RO; RW

Size:

32 bits

Controls functionality that is needed by Legacy (non-PCI Express aware) OS's during
run time.

Core

Current De-emphasis Level (CURDELVL):

Current De-emphasis Level –

1b -3.5 dB

0b -6 dB

When the Link is operating at 2.5 GT/s speed, this bit is
0b.

Table 70. LSTS2 - Link Status 2 Register (Sheet 2 of 2)

Table 71. PEGLC - PCI Express-G Legacy Control Register

Bit

Access

Default

Value

RST/

PWR

Description

31:3

00000000h

Core

Reserved

Core

PME GPE Enable (PMEGPE)
0 = Do not generate GPE PME message when PME is received.
1 = Generate a GPE PME message when PME is received. This

enables the processor to support PMEs on the PEG port
under legacy OSs.

Core

Hot-Plug GPE Enable (HPGPE)
0 = Do not generate GPE Hot-Plug message when Hot-Plug

event is received.

1 = Generate a GPE Hot-Plug message when Hot-Plug Event is

received. This enables the processor to support Hot-Plug
on the PEG port under legacy OSs

Core

General Message GPE Enable (GENGPE)
0 = Do not forward received GPE assert/deassert messages.
1 = Forward received GPE assert/deassert messages.

Summary of Contents for CELERON PROCESSOR P4505 - ADDENDUM












































































































































Search results

Summary of Contents for CELERON PROCESSOR P4505 - ADDENDUM

Reviews:

Related manuals for CELERON PROCESSOR P4505 - ADDENDUM

Brands by name

Popular brands

Intel CELERON PROCESSOR P4505 - ADDENDUM, Datasheet

Search results

Summary of Contents for CELERON PROCESSOR P4505 - ADDENDUM

Reviews:

Related manuals for CELERON PROCESSOR P4505 - ADDENDUM

Brands by name

Popular brands