Intel Atom E660 User Manual Download Page 7 | Manualshive

Page: 7 / 67

Intel Atom E660 User Manual Download Page 7

Intel

®

Atom™ Processor E660 with Intel

®

Platform Controller Hub EG20T Development Kit

January 2012

User Manual

Document Number: 324213-002

7

Introduction

1.0

Introduction

This manual describes the typical hardware set-up procedures, features, and usage of

the Intel

®

Atom™ Processor E660 with Intel

®

Platform Controller Hub EG20T

Development Kit. This document is written for evaluation by OEMs, system integrators,

and embedded system developers. The document defines all jumpers, headers, LED

functions, and their locations on the development platform along with subsystem

features. The document assumes basic familiarity in the fundamental concepts involved

with installing and configuring hardware for a personal computer system.

Note:

Read this document in its entirety prior to applying power to the reference platform.

Intel recommends having the schematic files and development kit boards present while

reading this document. The references in this document correlate to reference

designators and board properties of the Intel

®

Atom™ Processor E660 with Intel

®

Platform Controller Hub EG20T Development Kit.

provides quick start procedures.

1.1

About the Development Kit

The development kit includes the following:

• COM Express* Module with Intel

®

Atom™ Processor E660, 1GB DDR2 soldered

down memory, system management CPLD and SPI Flash.

• Carrier board with the Intel

®

Platform Controller Hub EG20T and other system

components and peripheral connectors for PCIe*, PCI, SDVO, SATA, USB, LAN,

LVDS, SD/SDIO/MMC, UART and audio interfaces.

• Timesys Fedora* Remix Linux operating system (pre-installed on the hard drive

included in the kit)

• Software CD with user’s guide, reference design materials, drivers and utilities
• SATA Gen2 hard drive
• USB floppy drive
• Power supply
• LVDS cable

The kit contents may be prepared with additional equipment (depending on options

made available to you at the time of purchase):

• LVDS panel
• VGA SDVO ADD2N card and display (instead of the LVDS display and LVDS cable)
• DVD-ROM drive
• Keyboard and mouse with PS/2 or USB interface (BIOS setting dependent)
• Chassis with ATX power supply (or AC adapter)

«
...
5
6
7
8
9
...
»

Summary of Contents for Atom E660




































































Reviews:

No comments