Intel 81341 Developer'S Manual Download Page 60 | Manualshive

Page: 60 / 1056

background image

Intel

®

81341 and 81342—Address Translation Unit (PCI-X)

Intel

®

81341 and 81342 I/O Processors

Developer’s Manual

December 2007

60

Order Number: 315037-002US

2.2.1

Inbound Transactions

Inbound transactions which target the ATU are translated and executed on the 81341

and 81342 internal bus. As a PCI target, the ATU is capable of accepting all PCI

memory read and write operations as either a 32-bit or a 64-bit PCI target. In the

conventional PCI mode Memory Write and Memory Write and Invalidate operations are

performed as posted operations and all memory read operations are performed as

delayed reads. In the PCI-X mode Memory Write, Memory Write Block, and Alias to

Memory Write Block operations are performed as posted operations and Memory Read

DWORD, Memory Read Block, and Alias to Memory Read Block operations are executed

as split transactions. The ATU is capable of accepting configuration read and write

cycles. In the conventional PCI mode, Configuration Writes are performed as delayed

memory write operations and Configuration Reads are performed as delayed read

operations. In the PCI-X mode, both Configuration Writes and Configuration Reads are

performed as split transactions.
Inbound memory write transactions have their addresses entered into the inbound

write address queue (IWADQ) and data entered into the inbound write data queue

(IWQ). The IWQ/IWADQ pair are capable of holding up to 4 write operations up to the

size of the data queue. Inbound configuration writes use the inbound delayed write

queue (IDWQ) for address and data. Refer to

for details of queue

operation. Inbound read operations (memory and configuration) have their address

entered into the inbound transaction queue (ITQ) and the data is returned to the PCI

master in the inbound read queue (IRQ). The ITQ is capable of holding up to 8 delayed

read requests (split read requests when operating in the PCI-X mode).
In the conventional PCI mode, for inbound transactions, the ATU is a slave on the PCI

bus and is a requester on the internal bus. PCI slave operation is defined in the PCI

Local Bus Specification, Revision 2.3. In the PCI-X mode, for inbound transactions, the

ATU initially is a target on the PCI bus and becomes an initiator when performing split

completion transactions, and is an initiator on the internal bus.
Operation of the internal bus is defined in

Chapter 6.0, “System Controller (SC) and

Internal Bus Bridge”

. Specific operation of the ATU as master on the internal bus is

defined in

.

«
...
58
59
60
61
62
...
»

Summary of Contents for 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 81341

PCMCIA WIRELESS ASAPTER DWL-650

Brand: D-Link Pages: 5

PowerLine DHP-W611AV

Brand: D-Link Pages: 78

Brand: 3Com Pages: 8

Brand: National Instruments Pages: 17

Brand: National Instruments Pages: 5

Brand: National Instruments Pages: 76

ROADRECORDER 8000

Brand: Safety Vision Pages: 40

Brand: Samsung Pages: 65

Brand: Industrex Pages: 51

Brand: Rajant Corporation Pages: 40

Advanced Flame 1.0

Brand: Eastern Voltage Research Pages: 12

Brand: ADTRAN Pages: 9

Brand: Idis Pages: 18

Brand: TANDBERG Pages: 2

Brand: Intellinet Pages: 2

Brand: BenQ Pages: 38

Brand: TRENDnet Pages: 2

Brand: Stepper Motor Canada Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands