Intel 81341 Developer'S Manual Download Page 58

Page: 58 / 1056

Intel

81341 and 81342—Address Translation Unit (PCI-X)

Intel

81341 and 81342 I/O Processors

Developer’s Manual

December 2007

Order Number: 315037-002US

2.2

ATU Address Translation

The ATU allows PCI masters on the PCI bus to initiate transactions to the 81341 and

81342 internal bus and allows the Intel XScale

processor (ARM* architecture

compliant) to initiate transactions to the PCI bus.
The ATU implements an address windowing scheme to determine which addresses to

claim and translate to the destination bus.

• The address windowing mechanism for inbound translation is described in

Section

2.2.1.1, “Inbound Address Translation” on page 61

• The address windowing mechanism for outbound translation is described in

Section

2.2.2, “Outbound Transactions- Single Address Cycle (SAC) Internal Bus

Transactions” on page 72

and

Section 2.2.3, “Outbound Write Transaction” on

page 77

The ATU has the ability to accept up to eight inbound PCI read transactions and four

inbound PCI write transactions simultaneously. Also, the ATU has the ability to accept

up to eight outbound internal bus read transactions and four outbound internal bus

write transactions simultaneously. Refer to

Figure 4

and

Section 2.6

for details of the

ATU queue architecture.
The ATU unit allows for recognition and generation of multiple PCI cycle types.

Table 1

shows the PCI and PCI-X commands supported for both inbound and outbound ATU

transactions. The type of operation seen by the ATU on inbound transactions is

determined by the PCI master who initiates the transaction. Claiming an inbound

transaction depends on the address range programmed within the inbound translation

window. The type of transaction used by the ATU on outbound transactions generated

by the core processor is determined by the internal bus address and the outbound

windowing scheme.
ATU supports the 64-bit addressing specified by the PCI Local Bus Specification,

Revision 2.3. This 64-bit addressing extension is supported for both inbound and

outbound data transactions. This is in addition to the 64-bit data extensions supported

by the 81341 and 81342.
ATU does not support exclusive access using the PCI LOCK# signal. Also, the ATU does

not insure atomicity for outbound transactions.

Note:

In conventional PCI Mode, the ATUX will pre-fetch data for read transactions on the

internal bus as defined in

Section 2.6.1.2, “Inbound Read Queue Structure” on

page 89

. For internal bus targets that are not capable of supporting large byte-counts

as indicated in

Table 8, “Inbound Read Prefetch Data Sizes” on page 89

, these internal

bus targets must be accessed using a non-prefetchable PCI window. This requirement

also includes access made to the north internal bus targets via the internal bus bridge.

The internal bus bridge supports 32-byte data queues, and any access made via the

internal bus bridge that is greater than 32 bytes will result in an internal bus target

abort.

Summary of Contents for 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 81341

Reviews:

Related manuals for 81341

Brands by name

Popular brands

Intel 81341, Developer'S Manual

Search results

Summary of Contents for 81341

Reviews:

Related manuals for 81341

Brands by name

Popular brands