Intel 80331 Design Manual Download Page 98

Page: 98 / 148

Intel® 80331 I/O Processor

Design Guide

Memory Controller

NOTE:

All traces except breakout TL8 traces are of the same impedance and spacing requirements.

Table 52.

Embedded DDR 333 Unbuffered Address/CMD Topology Lengths

Traces

Description

Layer

Minimum

Length

Maximum

Length

Trace

Impedance

Spacing

Notes

TL1

Microstrip/

Strip

1.5”

1.67”

45 ohms+/-15%
or 50 ohms
+/-15%

12 mils

TL1-TL6 as per JEDEC DDR1
Specifications (PC2700) to be
routed as T points

TL2

Microstrip

1.2 “

1.35”

Same as TL1

12 mils

TL3

Microstrip

0.5”

0.6”

Same as TL1

12 mils

Fan out for series termination
(only for unbuffered)

TL4

0.3”

0.35”

Same as TL1

12 mils

TL5

0.14”

0.18”

Same as TL1

12 mils

TL6

0.32”

0.35”

Same as TL1

12 mils

TL7

0.25”

0.5”

Same as TL1

12 mils

TL8

Breakout

Any

0”

0.5”

5 mils

TL9

Lead-in

Microstrip/

Stripline

1”

8”

45 ohms+/-15%
or 50 ohms
+/-15%

12 mils

Spacing: within the same
group 12 mils

With other groups 20 mils

TL10

VTT

Microstrip

0.25”

0.5”

5 mils

Place in VTT Island

Figure 47.

Embedded DDR 333 Unbuffered ADDR/CMD Topology

TL2

TL1

TL3

TL4

TL3

TL5

SDRAM Pin

TL3

SDRAM Pin

TL5

TL6

TL5

51 ohms

+/- 5%

TL7

VTT (1.25 V)

TL10

TL8

TL9

22 ohms

+/- 5%

SDRAM Pin

Summary of Contents for 80331





















































































































































Search results

Summary of Contents for 80331

Reviews:

Related manuals for 80331

Brands by name

Popular brands

Intel 80331, Design Manual

Search results

Summary of Contents for 80331

Reviews:

Related manuals for 80331

Brands by name

Popular brands