Intel 80331 Design Manual Download Page 56

Page: 56 / 148

Intel® 80331 I/O Processor

Design Guide

PCI-X Layout Guidelines

6.4.10

PCI-X 100 MHz Slot and Embedded Topology 2

Figure 24

and

Table 16

combine both a slots and an embedded device.

Figure 25.

Combination of Slots and Embedded PCI-X 100 MHz Routing Topology

Table 17.

Combination of Slot and Embedded PCI-X 100 MHz Routing 2 Recommendations
(Sheet 1 of 2)

Parameter

Routing Guideline for Lower AD Bus Routing Guideline for Upper AD Bus

Reference Plane

Preferred Layer

Route over an unbroken ground plane

Stripline

Breakout

5 mils on 5 mils spacing. Maximum length of the breakout is 500 mils.

Motherboard Trace
Impedance (microstrip and
stripline)

50 Ohms +/- 15%

Add-in card Impedance
(microstrip and stripline)

57 Ohms +/- 15%

Stripline Trace Spacing

12 mils, from edge to edge

Microstrip Trace Spacing

18 mils, from edge to edge

Group Spacing

Spacing from other groups: 25 mils minimum edge to edge

Trace Length 1 TL1: From
80331signal Ball to first
junction

1.5” minimum - 4.25” maximum

1.5”minimum - 3.75” maximum

Trace Length TL2 - first
junction to First PCI
Connector

0.0” minimum to 1.0” maximum

Trace Length TL3 - First PCI
Connector to Second PCI
Connector

0.8” minimum - 1.2” maximum

Trace Length TL_EM1 - from
first junction to the
Embedded Device.

1.0” minimum - 3.25” maximum

TL1

TL2

CONN2

TL_

AD2

L_E

EM1

CONN1

AD1

L_A

TL3

Summary of Contents for 80331





















































































































































Search results

Summary of Contents for 80331

Reviews:

Related manuals for 80331

Brands by name

Popular brands

Intel 80331, Design Manual

Search results

Summary of Contents for 80331

Reviews:

Related manuals for 80331

Brands by name

Popular brands