Integra DTR-40.5, Instruction Manual

Page: 71 / 104

Advanced Operations
En-71
Operating
procedure
(
➔
page 55 )
■
Audio TV Out (Main)
`
Off
`
On
This preference determines whether the incoming
audio signal is output from
HDMI OUT MAIN . You
may want to turn this preference on if your TV is
connected to
HDMI OUT MAIN and you want to listen
to the audio from a connected component through
your TV’s speakers. Normally, this should be set to
“
Off ”.
Note
• If “ On ” is selected and the audio can be output from the TV,
the AV receiver will output no sound through its speakers.
In this case, “
TV Speaker ” appears on the AV receiver’s
display by pressing Display .
• When “ HDMI CEC (RIHD) ” is set to “ On ”, this setting is
fixed to “ Auto ”.
• This setting is fixed to “ Off ” when “ Monitor Out ” is set to
“ Sub ” (
➔
page 56 ).
• With some TVs and input signals, no sound may be output
even when this setting is set to “ On ”.
• When “ Audio TV Out (Main) ” or “ HDMI CEC (RIHD) ” is set
to “ On ” and you’re listening through your TV’s speakers,
turning up the AV receiver’s volume control will make the
sound be output from the AV receiver’s front left and right
speakers. To stop the AV receiver’s speakers producing
sound, change the settings, change your TV’s settings, or
turn down the AV receiver’s volume.
• Listening mode cannot be changed when this setting is set
to “ On ” and the audio is output from the TV.
• If the audio signal from the player is not supported by the
TV, the audio is not output from the TV even if this setting
is enabled. When the audio cannot be output from the TV,
(When “
Monitor Out ” is set to “ Both ”, the audio cannot be
output form the TV connected to both HDMI OUT MAIN and
HDMI OUT SUB ) the audio is output from the speakers
connected to the AV receiver.
■
Audio TV Out (Sub)
`
Off
`
On
This preference determines whether the incoming
audio signal is output from
HDMI OUT SUB . You may
want to turn this preference on if your TV is
connected to
HDMI OUT SUB and you want to listen
to the audio from a connected component through
your TV’s speakers. Normally, this should be set to
“
Off ”.
Note
• If “ On ” is selected and the audio can be output from the TV,
the AV receiver will output no sound through its speakers.
In this case, “
TV Speaker ” appears on the AV receiver’s
display by pressing Display .
• This setting is fixed to “ Off ” when “ Monitor Out ” is set to
“ Main ” (
➔
page 56 ).
• When “ Monitor Out ” is set to “ Both ” (
➔
page 56 ), and this
setting is enabled, set audio output of source component to
2ch PCM.
• With some TVs and input signals, no sound may be output
even when this setting is set to “ On ”.
• When “ Audio TV Out (Sub) ” is set to “ On ” and you’re
listening through your TV’s speakers, turning up the AV
receiver’s volume control will make the sound be output
from the AV receiver’s front left and right speakers. To stop
the AV receiver’s speakers producing sound, change the
settings, change your TV’s settings, or turn down the AV
receiver’s volume.
• Listening mode cannot be changed when this setting is set
to “ On ” and the audio is output from the TV.
• When “ Monitor Out ” is set to “ Both ” (
➔
page 56 ) and only
“ Audio TV Out (Sub) ” is set to “ On ”, the audio is not output
from the TV connected to HDMI OUT SUB except in the
case the audio input is via HDMI.
• If the audio signal from the player is not supported by the
TV, the audio is not output from the TV even if this setting
is enabled. When the audio cannot be output from the TV,
(When “
Monitor Out ” is set to “ Both ”, the audio cannot be
output form the TV connected to both HDMI OUT MAIN and
HDMI OUT SUB ) the audio is output from the speakers
connected to the AV receiver.
■
Audio Return Channel
`
Off
`
Auto :
The audio signal from your TV tuner can be sent
to
HDMI OUT MAIN of the AV receiver.
The audio return channel (ARC) function allows an
ARC capable TV to send the audio stream to
HDMI
OUT MAIN of the AV receiver. To use this function,
you must select the TV/CD input selector and your TV
must be ARC capable. The ARC indicator will light
when the audio signal is detected. Default setting:
“
- - - -
”
Note
• This setting is fixed to “ - - - - ” when the “ HDMI CEC (RIHD) ”
setting is set to “ Off ”.
• This setting is set to “ Auto ” automatically when the “ HDMI
CEC (RIHD) ” setting is set to “ On ” for the first time.
• If you set “ Audio Return Channel ” to “ Auto ”, the “ Audio
Selector ” settings of the TV/CD input selector will be
automatically switched to “ ARC ” (
➔
page 67 ).
Tip
• After changing the settings of the “ HDMI CEC (RIHD) ”,
“ HDMI Through ” or “ Audio Return Channel ”, turn off the
power on all connected pieces of equipment and then turn
them on again. Refer to the user’s manuals for all
connected pieces of equipment.
■
Lip Sync
`
Off
`
On
This function allows the AV receiver to automatically
correct any delay between the video and the audio,
based on the data from the connected monitor.
Note
• This function works only if your HDMI-compatible TV
supports HDMI Lip Sync.