background image

Functional Description 

INSYS GSM 4.3 easy 

 

 

Theoretically it is possible to set all other object instances, too. INSYS MI-
CROELECTRONICS recommends paralleling the corresponding registers 
within the configuration program of the easy to avoid impact on the proper 
function of the easy objects. E.g. it is not recommended to switch objects 
like digital inputs directly. On the other hand it is uncritical to set a parallel 
connected bit register to simulate the setting of digital input within the 
configuration program (e.g. imitate the triggering of a sensor). 

5.3.4

 

Status Query 

Command: 

STATUS?,CN:[ Callback] 

This reply indicates the status of the easy device. 
The query of the status is performed up to three times, if necessary. If there is still no re-
ply from the easy device, an SMS with the text „

NO SUCCESS

“ is sent instead of the 

status SMS. 
Of course, a callback number („

CN:

“) is required. This means that you have to enter at 

least the character string „

CN

:”. If another callback number is desired, after the character 

string „

CN:

” an additional space character and the phone number must be entered (see 

previous example). 
 
The response may contain the following: 

Status 

Meaning 

 

RUN 

The easy device is in operating mode RUN 

STOP 

The easy device is in operating mode STOP 

NO SUCCESS 

The easy device does not reply (cable not connected, etc.) 

Table 6: Possible replies to a status query 

5.3.5

 

Status Change 

Command: 

STATUS=<easy-Status>[,CN: [Callback]] 

 

easy-Status 

Meaning 

 

RUN 

Switch on easy device, run control program 

STOP Switch 

off 

easy 

device, terminate control program 

Table 7: Possible status changes 

 
The query of the status to the easy device is performed up to three times, if necessary. If 
there is still no reply from the easy device, an SMS with the text „

NO SUCCESS

“ is sent 

instead of „

OK

“. 

If the easy device does not acknowledge the status change, the reply SMS will send the 
message „

ERROR

“. This can also occur when a status is set in which the easy device is 

already running. 
A callback number („

CN

:“) is not required. Without a callback number, however, there 

20 

 

Summary of Contents for GSM 4.3 easy



























Reviews: