background image

 

Page 15 of 16 

2453-222/2453-422/2453-522 - Rev: 1/21/2014 7:51 AM  

Certification and Warranty 

Certification 

This product has been thoroughly tested by ITS ETL SEMKO, a nationally recognized independent third-party testing laboratory. The North American ETL Listed mark 
signifies that the device has been tested to and has met the requirements of a widely recognized consensus of U.S. and Canadian device safety standards, that the 
manufacturing site has been audited, and that the manufacturer has agreed to a program of quarterly factory follow-up inspections to verify continued conformance.  

FCC and Industry Canada Compliance Statement 

This device complies with FCC Rules Part 15 and Industry Canada RSS-210 (Rev. 7). Operation is subject to the following two conditions: 

(1) This device may not cause harmful interference, and  
(2) This device must accept any interference, including interference that may cause undesired operation of the device. 

Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions 
suivantes:  

(1) l'appareil ne doit pas produire de brouillage, et  
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. 

The digital circuitry of this device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits 
are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses, and can radiate radio frequency 
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio and television reception. However, there is no 
guarantee that interference will not occur in a particular installation. If this device does cause such interference, which can be verified by turning the device off and on, 
the user is encouraged to eliminate the interference by one or more of the following measures: 

-  Re-orient or relocate the receiving antenna of the device experiencing the interference 
-  Increase the distance between this device and the receiver 
-  Connect the device to an AC outlet on a circuit different from the one that supplies power to the receiver 
-  Consult the dealer or an experienced radio/TV technician 

WARNING: Changes or modifications to this device not expressly approved by the party responsible for compliance could void the user’s authority to operate the 
equipment.  

Declaration of Conformity 

Hereby, INSTEON declares that this device is in compliance with the essential requirements and other relevant provisions of the following Directives: 
1) Low Voltage Equipment Directive 2006/95/EC 
2) Electromagnetic Compatibility Directive 2004/108/EC 
3) Hazardous Substance Directive 2005/95/EC 
Technical data and copies of the original Declaration of Conformity are available and can be obtained from INSTEON; 16542 Millikan Ave, Irvine, CA, USA. 
User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE) 
This document contains important information for users with regards to the proper disposal and recycling of INSTEON products. Consumers are required to comply 
with this notice for all electronic products bearing the following symbol:

 

 

 

Environmental Information for Customers in the European Union 
European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal 
waste. The symbol indicates that this product should be disposed of separately from regular household waste streams.  
It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. 
Correct disposal and recycling will help prevent potential negative consequences to the environment and human health.  
For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased 
the product. 
 
DECLARATION OF CONFORMITY TO R&TTE DIRECTIVE 1999/5/EC for the European Community, Switzerland, Norway, Iceland and Liechtenstein 
Product category: general consumer (category 3). 
English: This equipment is in compliance with the essential requirements and other relevant provisions of the European R&TTE Directive 1999/5/EC 
Deutsch [German]: Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren entsprechenden Vorgaben der Richtlinie 1999/5/EU. 
Nederlands [Dutch]: Dit apparaat voldoet aan de essentiele eisen en andere van toepassing zijnde bepalingen van de Richtlijn 1999/5/EC. 
Svenska [Swedish]: Denna utrustning står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 
1999/5/EG. 
Français [French]: Cet appareil est conforme aux exigences essentielles et aux autres dispositions pertinentes de la Directive 1999/5/EC 
Español [Spanish]: Este equipo cumple con los requisitos esenciales asi como con otras disposiciones de la Directiva 1999/5/CE. 
Português [Portuguese]: Este equipamento está em conformidade com os requisitos essenciais e outras provisões relevantes da Directiva 1999/5/EC. 
Italiano [Italian]: Questo apparato é conforme ai requisiti essenziali ed agli altri principi sanciti dalla Direttiva 1999/5/CE. 
Norsk [Norwegian]: Dette utstyret er i samsvar med de grunnleggende krav og andre relevante bestemmelser i EU-direktiv 1999/5/EF. 
Suomi [Finnish]:Tämä laite tÿttää direktiivin 1999/5/EY olennaiset vaatimukset ja on siinä asetettujen muiden laitetta koskevien määräysten mukainen. 
Dansk [Danish]: Dette udstyr er i overensstemmelse med de væsentlige krav og andre relevante bestemmelser i Direktiv 1999/5/EF. 

Polski [Polish]: Urządzenie jest zgodne z ogólnymi wymaganiami oraz szczególnymi warunkami okreslonymi Dyrektywą UE: 1999/5/EC 

Limited Warranty 

Seller warrants to the original consumer purchaser of this product that, for a  period of two years from the date of purchase, this product will be free from defects in 
material and workmanship and will perform in substantial conformity to the description of the product in this Owner’s Manual. This warranty shall not apply to defects or 
errors caused by misuse or neglect. If the product is found to be defective in material or workmanship, or if the product does not perform as warranted above during the 
warranty period, Seller will either repair it, replace it, or refund the purchase price, at its option, upon receipt of the product at the address below, postage prepaid, with 
proof of the date of purchase and an explanation of the defect or error. The repair, replacement, or refund that is provided for above shall be the full extent of Seller’s 
liability with respect to this product. For repair or replacement during the warranty period, call INSTEON at 866-243-8022 with the Model # and Revision # of the device 
to receive an RMA# and send the product, along with all other required materials to:  

 
INSTEON 
ATTN: Receiving 
16542 Millikan Ave. 
Irvine, CA 92606-5027 

Summary of Contents for 2453-222

















Reviews: